A grass seed calculator works out how much seed a lawn needs from its area and a seeding rate. Pick the shape of the lawn, enter its size, choose a grass type and the calculator shows a low and a high amount for a new lawn, or uses your own rate for overseeding.
How to use the grass seed calculator
- Choose US or Metric and the lawn shape.
- Enter the size of the lawn.
- Choose new lawn and a grass type, or type your own seeding rate if you are overseeding.
- Press Work out the seed.
The basic formula
The seed needed is the seeding rate times the lawn area, divided by 1,000, where the rate is in pounds per 1,000 square feet, the unit the extension pages use [1][2]. The formula is our own working. A rate of 2 pounds per 1,000 square feet over a lawn of 2,000 square feet is therefore 4 pounds. The same formula works with any rate that you type. The calculator then converts the result to kilograms, using 0.4536 kilogram per pound, which is our own conversion.
Area of the lawn
The calculator finds the area for four shapes. A rectangle is width times length, a circle is pi times the radius squared, an ellipse is pi times its two semi-axes and a triangle is half the base times the height. These are standard geometry formulas. For the ellipse, we label the two inputs as semi-axes, meaning half of the full width and half of the full length. In metric mode the area is converted to square feet before the rate is applied.
Rates for a new lawn
The extension pages give rates in pounds per 1,000 square feet for seeding a new lawn. Rutgers gives about 2 for Kentucky bluegrass, 4 to 6 for tall fescue, 4 to 6 for fine fescues and 4 to 6 for perennial ryegrass [1]. Penn State gives 2 to 3 for Kentucky bluegrass alone, 6 to 8 for turf-type tall fescue, 4 to 5 for fine fescue and 4 to 5 for perennial ryegrass [2]. The calculator uses the lowest and the highest of the two pages for each grass.
The ranges in the calculator
This gives 2 to 3 for Kentucky bluegrass, 4 to 8 for tall fescue, 4 to 6 for fine fescue and 4 to 6 for perennial ryegrass. Taking the span of two sources is our own working, so the result is shown as a low and a high amount of seed. The tall fescue range is wide because one page covers turf-type fescue at a higher rate. The page of Penn State notes that its rates assume seed of at least a minimum purity and germination [2].
A worked example
A rectangular lawn of 50 by 40 feet has an area of 2,000 square feet. For Kentucky bluegrass at 2 to 3 pounds per 1,000 square feet, you need 4 to 6 pounds of seed, which is 1.8 to 2.7 kilograms. A circular lawn of radius 50 feet has an area of 7,854 square feet, and at a rate of 5 pounds it needs 39.27 pounds.
Overseeding
The pages we read do not give an overseeding rate for lawns. Rutgers gives rates for new seeding only [1]. Cornell lists overseeding rates for sports fields, such as 2.5 to 3.5 pounds for Kentucky bluegrass and 10 to 15 for perennial ryegrass or tall fescue, which are not meant for home lawns [3]. So the calculator has no built-in overseeding rate. Choose the overseeding option and type the rate printed on your seed label. The calculator then applies it to the area.
Using your own rate
You can also type a rate for a new lawn, for example from your seed label or your local advice. The calculator then uses only that rate, instead of the low and high range. In metric mode the rate is in kilograms per 1,000 square metres, and one pound per 1,000 square feet is 4.88 kilograms per 1,000 square metres, which is our own conversion of the units.
Seed quality
The rates only hold for good seed. Penn State assumes minimum purity and germination figures [2], and low quality seed needs more of it. Read the label for the percentage of pure live seed, and the date of the germination test. Mixes of several grasses, and shade mixes, have their own rates, so a mix may need a different amount than the single species in the calculator.
What the pages do not say
The pages do not give one rate that works for every region, and Rutgers gives no overseeding rate. Buffalo grass has no extension rate in the pages we read, so for it you should type your own rate.
Using the calculator
Measure the lawn, break an odd shape into a rectangle, a circle or a triangle if you need to, and add the seed for each part. Round the answer up to the next bag size. The result is a guide to the amount to buy, and good soil preparation and watering matter as much. The calculator keeps your numbers in your browser and sends nothing.
Common mistakes
- Using the wrong units for the rate. The rate is per 1,000 square feet, or per 1,000 square metres in metric mode.
- Entering the full axis of an ellipse. Enter half the width and half the length.
- Expecting an overseeding rate. Type the rate from your label.
- Ignoring seed quality. Poor seed needs a higher rate.
- Forgetting several shapes. Split an odd lawn into parts.
What next
Use this often? Add Grass Seed to your Home screen.
Frequently asked questions
What is a grass seed calculator?
A tool that works out the seed needed for a lawn from its area and a seeding rate in pounds per 1,000 square feet.
How much grass seed do I need for a new lawn?
For Kentucky bluegrass the extension pages give 2 to 3 pounds per 1,000 square feet, so a 2,000 square foot lawn needs 4 to 6 pounds.
What is the seed formula?
Seed equals the seeding rate times the lawn area, divided by 1,000, with the rate in pounds per 1,000 square feet.
Does it give an overseeding rate?
No. The pages we read give none for home lawns, so you type the rate from your seed label.
Why does the tall fescue range look wide?
Rutgers gives 4 to 6 and Penn State gives 6 to 8 for turf-type tall fescue, and the calculator shows the span of both.
Do rates change with seed quality?
Yes. Rates assume good, pure, live seed, and poorer seed needs more.
Sources
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.