A grade curve calculator raises a set of test scores by a rule that you choose, so that the results better match what the test was meant to measure. Enter the raw scores, pick a method, and see every score before and after, with the mean and spread of the class.
How to use the grade curve calculator
- Enter the raw scores, one after another.
- Choose a curve method.
- Set the maximum score, or the target mean and spread for the bell curve.
- Press the button to see the curved scores.
What curving does
Grading on a curve changes the raw scores of a class according to a rule, usually because a test was harder than expected. Wikipedia describes grading on a curve as assigning grades so as to approach a pre-specified distribution, such as a normal distribution [3]. There are several ways of doing it, and the choice between them is up to the teacher. The calculator offers four common methods and shows the result for every score, so that you can compare them on your own data before you decide which one is fair.
Adding points
The simplest curve adds a fixed number of points to every score, chosen so that the best score becomes 100 percent. The new score is the old score plus 100 minus the highest score. For the scores 80, 70, 90, 55, 60 and 80, the highest is 90, so every student gets 10 points, giving 90, 80, 100, 65, 70 and 90. This method and its example are our own working. The tool replaces 100 by the maximum possible score that you enter, which is our own generalization, so a 50 point test works too.
Scaling to the top score
Another method divides each score by the highest score, and multiplies by 100, written T = 100 × X ÷ Xmax [1]. As an example, with a highest score of 80, a score of 60 becomes 60 divided by 80, times 100, which is 75. Every score is multiplied by the same factor, so the best score becomes the maximum and the gaps between students grow in proportion. The maximum score in the tool is our generalization of the 100 in the formula.
The square root curve
The square root method takes the square root of the score and multiplies by 10, which suits a test out of 100. This method is our own working, and the figures are plain arithmetic. For example, 36, which becomes 60, 64, which becomes 80, 81, which becomes 90, and 100, which stays 100. This method lifts low scores a lot and high scores very little. For a test with another maximum, we use the square root of the score times the maximum, which reduces to 10 times the root when the maximum is 100. That extension is our own.
The bell curve
The bell curve method fits the scores to a target mean and a target standard deviation. Each score becomes the target mean plus its z-score times the target standard deviation. The z-score is the score minus the class mean, divided by the class standard deviation, z = (X − M) ÷ s [1][2]. Mapping the z-score onto a new mean and spread is our own working. You enter a target mean, such as 75, and a target spread, such as 12.
The bell curve example
Take the ten scores 80, 80, 75, 60, 60, 55, 50, 50, 40 and 25. Their mean is 57.5 and their standard deviation is 16.77, and with a target of 75 and 12 the new scores run from 91.1 for the 80s to 51.74 for the 25. The calculator gives the same numbers. This example is our own working. It uses the population standard deviation, which divides by the number of scores and treats the class as the whole group [2].
Reading the before and after
Under the list of scores, the calculator shows the mean, the standard deviation and the highest score before and after the curve, for the whole class. After the bell curve, the new mean and spread equal your targets. After adding points, the mean goes up by the points added and the spread stays the same. After scaling, both the mean and the spread are multiplied by the same factor. These checks are our own, and help you see what each method does to the class as a whole.
Scores above the maximum
A strong curve can push a score above the maximum, for example when the target mean is high in the bell curve. The calculator does not cap these scores. It shows the unclamped value and warns you how many scores are above the maximum or below 0, so that you can decide what to do. This is our own design. Whether to cap, to rescale, or to choose a milder target is the teacher's decision.
Entering the scores
Type or paste the scores in the box, separated by commas, spaces, semicolons or new lines. Negative numbers and words are rejected. A score above the maximum is an error, since a raw score cannot exceed the possible total. You can enter up to 2,000 scores. Only the first 60 are listed in the result to keep it readable, and the statistics use them all.
Fairness and choice
The method is up to the teacher. Adding points keeps the order and the gaps. Scaling widens the gaps. The square root helps low scores most. The bell curve forces a shape on the class, and can lower the marks of strong students in a very good class. In our own view, adding points and scaling are gentle, while the bell curve can lower the marks of strong students in a very good class. There is no single right answer. Try each method on your own scores, look at the before and after, and choose the one that is closest to what the test was supposed to show.
Common mistakes
- Applying a bell curve to a very small class. A few scores give a poor estimate of the spread.
- Using the sample standard deviation. This tool divides by the number of scores.
- Curving above the maximum. Check the warning line.
- Choosing a method without comparing. Try all four on the same scores.
What next
Use this often? Add Grade Curve to your Home screen.
Frequently asked questions
What is a grade curve calculator?
It is a tool that raises a set of test scores by a rule such as adding points, scaling to the top score, a square root or a bell curve, and shows each score before and after.
How do I grade on a curve by adding points?
Add the same number of points to every score so that the highest score becomes the maximum. If the best score is 90 out of 100, add 10 points to every score.
What is the square root curve?
The new score is 10 times the square root of the old score on a 100 point test. A score of 36 becomes 60 and a score of 64 becomes 80.
How does the bell curve method work?
Each score becomes the target mean plus its z-score times the target standard deviation, where the z-score uses the class mean and the population standard deviation.
Does the calculator cap scores at the maximum?
No. It shows the curved value as it is and warns you if any score ends above the maximum or below 0, so you can decide what to do.
Sources
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.