Saved

Press the star next to a tool's name to save it.

All my tools

Efficiency Calculator

Use this efficiency calculator to find the energy conversion efficiency of a machine from its output and input, find an output or input from an efficiency, or work out a heat pump's COP.

Restored your last values ·

Choose what you want to find. Enter the input and the useful output in the same unit, or an efficiency in percent. For a heat pump or an air conditioner, use the coefficient of performance mode.

Everything is worked out in your browser. Nothing you type is sent anywhere.

–

–

Choose what you want and fill in the boxes, then press Calculate.

See full result

An efficiency calculator finds the energy conversion efficiency of a machine from its useful output and its input, or finds the output or the input from a known efficiency. It also works out the coefficient of performance for heat pumps and air conditioners, which can be above 100 percent.

How to use the efficiency calculator

  1. Choose what you want.
  2. Enter the input, the output or the efficiency.
  3. Press Calculate.

The definition

Energy conversion efficiency is the ratio between the useful output of an energy conversion machine and the input, in energy terms: η = P_out ÷ P_in [1]. It ranges from 0 to 1, or from 0 to 100 percent, and the page says that efficiencies cannot exceed 100 percent [1]. The difference between the input and the useful output is lost, often as heat.

A worked example

A motor that takes 1,000 watts from the supply and delivers 800 watts at the shaft has an efficiency of 80 percent, and loses 200 watts. At 95 percent, an input of 1,000 watts gives 950 watts of output. To deliver 950 watts at 95 percent efficiency, you need an input of 1,000 watts. The calculator does each of these, in any unit, provided that the input and output use the same one.

Typical efficiencies

The page gives some figures: a gas turbine converting chemical energy to electricity reaches up to 40 percent, and a gas turbine with a steam turbine, a combined cycle, up to 63.08 percent [1]. A water turbine in a hydroelectric plant reaches up to 95 percent, and an isolated horizontal-axis wind turbine up to 50 percent [1]. Use them to judge whether an efficiency that you enter is realistic.

Water electrolysis

The page gives a worked example for the electrolysis of water. At 1.48 volts, the electrical input is 1.20 times the theoretical minimum, so the energy efficiency is 0.83 [1]. Another example is a low-pressure sodium lamp, with 200 lumens per watt against a theoretical maximum of 525, a luminous efficiency of 38.1 percent [1]. Both show that efficiency can be defined for other kinds of output.

Coefficient of performance

A heat pump or an air conditioner is not described by an efficiency but by the coefficient of performance, the COP [1]. It is the heat delivered divided by the work put in, so it can be above 1, because the machine moves heat instead of only converting work. The page says that most air conditioners have a COP of 2.3 to 3.5 [1]. A COP of 3 means 3 kilowatts of heat for 1 kilowatt of electricity.

Losses

The energy that is not delivered as useful output is lost, and in most machines it ends up as heat. The calculator shows the loss as the difference between the input and the output. In an electric motor, the loss is mainly in the windings and the bearings. In an engine, most of it goes out with the exhaust and the coolant.

Choosing the mode

Use the first mode to rate a machine from measurements. Use the second to find how much useful output you get from a given input, for example how much heat an electric heater gives out for the electricity it takes, which at 100 percent is all of it. Use the third to find how much input you need for a required output, for sizing a supply.

Units

The input and the output can be in any unit, such as watts, kilowatt-hours, joules or litres of fuel, as long as both are in the same one. The efficiency is dimensionless and is given as a percentage and a decimal. If the output is an energy and the input a power, divide by the time first to bring them to the same kind.

Limits

The calculator treats a single conversion. For a chain of machines, multiply the efficiencies: a motor of 90 percent driving a pump of 70 percent gives 63 percent overall. Efficiency also changes with the load, so a figure measured at full load may not hold at part load. The heating value of fuels, high or low, changes the figure, and should be stated.

Using the calculator

Pick the mode, enter the two values and press the button. The result shows the loss, and for the output and input modes the missing value. Check that the efficiency is realistic. For a heat pump, use the COP mode with the heat that it delivers and the work that it uses.

Efficiency of a chain

When machines are connected in a chain, the overall efficiency is the product of the stages. A generator of 95 percent, a transformer of 98 percent and a line of 96 percent give 89.4 percent overall. A chain with a poor stage cannot be better than that stage. Use the calculator for each stage and multiply the results to find the overall figure for a system. This is our own arithmetic.

Common mistakes

  • Comparing energy with power. Use the same kind of quantity.
  • Expecting more than 100 percent. Only a heat pump's COP can.
  • Multiplying the wrong way for a chain. Multiply the efficiencies.
  • Ignoring part-load behaviour. Efficiency varies with load.

What next

Use this often? Add Efficiency to your Home screen.

Frequently asked questions

What is an efficiency calculator?

A tool that finds the ratio of useful output to input for a machine.

What is the efficiency formula?

η = P_out ÷ P_in.

Can the efficiency be above 100 percent?

No. A heat pump has a COP above 1, but that is not an efficiency.

What is a typical COP of an air conditioner?

About 2.3 to 3.5.

How do I find the efficiency of a chain of machines?

Multiply the efficiencies of the stages.

What went wrong?

We only receive the reason you pick, never what you typed into the tool.

Thanks for your feedback.

More Physics & Science Tools