Saved

Press the star next to a tool's name to save it.

All my tools

Dimensional Analysis Calculator

This dimensional analysis calculator converts a measurement with the factor-label method. Enter your value and unit, then up to three conversion factors written as "1 mi = 1.609344 km". It multiplies them through and shows each unit cancelling.

Restored your last values ·

Type the value and its unit. Then write each conversion factor as "amount unit = amount unit". Factor 1 is needed. Factors 2 and 3 are optional and are used in order.

Everything is worked out in your browser. Nothing you type is sent anywhere.

–

–

Enter a value, its unit and at least one conversion factor.

What this dimensional analysis calculator does

Dimensional analysis, also called the factor-label method, is a way to convert units by multiplying by fractions that equal one. This dimensional analysis calculator does the multiplication and the cancelling for you. You supply a value and a chain of up to three conversion factors, and it shows the result, the working and the overall factor.

The idea comes from a simple rule. A conversion factor is described as a quotient that converts one unit of measure into another without changing the quantity. [1] Since any quantity can be multiplied by 1 without changing it, you can multiply by a factor, and the old unit cancels while the new one stays. [1]

How to use the calculator

  1. Type the starting value and its unit, such as 60 and mi.
  2. In Factor 1, write a relationship between two units, such as 1 mi equals 1.609344 km. Type the first amount and unit, then the second amount and unit.
  3. If one step is not enough, fill Factor 2 and Factor 3. Each factor must contain the unit you currently have.
  4. Press Calculate. You get the final value with its unit, the working with each cancellation, and the single overall factor.

You can write a factor in either direction. If the current unit is the second unit of a factor, the calculator flips the fraction for you, so you do not have to think about which side goes on top.

How the factors are applied

Each factor reads "a unit1 = b unit2". If you currently hold unit1, you multiply by b over a, and unit1 cancels, leaving unit2. If you hold unit2, you multiply by a over b instead. The calculator checks the unit name against both sides ignoring capital letters and extra spaces, so Km and km match.

This is the same cancelling shown on the Wikipedia page. There, a pressure in bar is multiplied by a ratio of kilopascals to bars, the bars cancel out, and 5 bar becomes 500 kPa. [1]

Worked example: miles to kilometres

Convert 60 mi to km with one factor, 1 mi = 1.609344 km. The calculator multiplies 60 by 1.609344 and divides by 1. The miles cancel, so the answer is 96.56064 km. The overall factor is 1.609344 km per mi.

Worked example: hours to seconds in two steps

Convert 2 h to s. Factor 1 is 1 h = 60 min and Factor 2 is 1 min = 60 s. The working is 2 h times 60 min over 1 h, which leaves 120 min, then times 60 s over 1 min, which leaves 7,200 s. The overall factor is 3,600 s per h.

StartFactor 1Factor 2Answer
2 h1 h = 60 min1 min = 60 s7,200 s
100 cm1 m = 100 cmnone1 m
60 mi1 mi = 1.609344 kmnone96.56064 km

Tips for setting up factors

  • Write each factor as a true statement of equality, for example 1 kg = 1000 g.
  • Use the same spelling for the same unit in every box, including the starting unit.
  • Put the factors in the order of the journey: from your unit toward the goal unit.
  • Use exact definitions where they exist, and say so when a figure is rounded.
  • For a derived unit such as miles per hour, convert the top and bottom one after the other.

Common mistakes

  • Typing a factor that does not contain the unit you currently hold. The calculator then reports that the unit does not match.
  • Mixing names, such as m and meter. Choose one form and keep it.
  • Using a rounded factor and then trusting too many digits in the answer.
  • Forgetting that the second factor starts from the unit the first factor produced, not from the original unit.

The tool does not know which factors are correct in the real world. It multiplies what you give it. That is a strength for study, because you decide each step, but it means a wrong factor gives a wrong answer. Always compare the final unit with the unit you wanted.

Why this method works

Because each factor equals 1, multiplying by it changes only how the quantity is written, not its size. Units behave like algebra symbols, so a unit on top cancels the same unit below. That is why the final unit is a reliable check: if it is not the unit you wanted, a factor is wrong or upside down.

A longer example with three factors

Suppose a car travels at 60 mi per hour and you want the distance in kilometres after 1 day. Start with 1 d, then use 1 d = 24 h, 1 h = 60 min and 1 min = 60 s to reach seconds. In practice many people simply multiply their way to the unit they need, and this tool keeps the record of each step. When a chain is longer than three factors, finish the first three, copy the result and use it as the starting value for the next run.

Using it for study and homework

In chemistry and physics classes, teachers often ask students to show every unit in a working. This calculator prints that working as text, so you can compare it with your own page. If your answer and the calculator disagree, look at the unit at each stage. The step where the unit stops cancelling is usually where the mistake is, for example a factor typed upside down or a missing step.

When a factor includes powers

Some conversions involve squared or cubed units, such as square metres or cubic feet. In that case, write the factor for the squared unit as a whole, for example 1 m2 = 10.7639 ft2, and use the same spelling in the starting unit. The calculator treats a unit name as a label, so it cannot work out the square of a factor for you. Writing the full factor yourself keeps the method honest.

What next

Use this often? Add Dimensional to your Home screen.

Frequently asked questions

What is dimensional analysis?

It is a way of converting units by multiplying by conversion factors that equal one, so that unwanted units cancel and the wanted unit remains.

How do I use a dimensional analysis calculator?

Enter the starting value and unit, then write each conversion factor as an equality between two units. The calculator multiplies them in order and shows the cancelling.

Can this dimensional analysis calculator flip a factor?

Yes. If your current unit is the second unit in a factor, the calculator uses the inverse for you.

Why does it say the unit does not match?

The unit you hold must appear in the next factor, spelled the same way. Check spelling and the order of your factors.

How many factors can I use?

Up to three, used in order. For longer chains, run the calculator again with the first result as the new starting value.

What went wrong?

We only receive the reason you pick, never what you typed into the tool.

Thanks for your feedback.

More Education Tools