A deck stain calculator turns the size of a deck into the amount of stain to buy. Enter the floor, the railing and the steps, add the number of coats and the coverage printed on the can, and the tool gives the area to stain and the stain needed in gallons or litres. It also adds a buy figure rounded up to a quarter gallon. Stain makers say most decks need one to two coats [1].
How to use the deck stain calculator
- Choose US or metric units.
- Enter the floor length and width of the deck.
- Add the railing length and height and the steps if you will stain them.
- Enter the number of coats and the coverage on the can, or leave them blank for one coat and the default.
- Press Calculate.
The three areas that are added
The calculator adds up the floor, the railing and the steps. The floor area is the length times the width. The railing area is the railing length times its height, which is a rough estimate. The steps area is the number of steps times the step width times the sum of the run and the rise, so it counts the tread and the riser of every step. These area formulas are our own working. The three areas are added into one total, and that total is divided by the coverage of the stain. If you leave the railing or the steps blank, they are left out, so you can stain the floor alone.
From area to gallons
Once you know the total area, the stain needed is the area divided by the coverage of one gallon, and when you plan more than one coat the amount is multiplied by the number of coats. Sherwin-Williams says that one gallon typically covers about 250 to 350 square feet, depending on the wood type [1]. The tool starts from a more cautious default of 175 square feet per gallon, which is our own planning figure, and if the coverage on your can is different, type it in and the tool uses your figure instead. The answer is shown in gallons and in litres, with 3.785 litres to the US gallon, which is our own conversion. In metric mode the order is reversed, and litres come first.
A worked example for a plain floor
A deck floor of 20 by 20 feet has an area of 400 square feet. At 175 square feet per gallon, one coat needs 400 divided by 175 = 2.286 gallons, and two coats need 4.571 gallons. The tool shows 2.286 gallons and then, as its own rule, tells you to buy 2.5 gallons, because rounding up to the next quarter gallon leaves a small margin instead of running out halfway through the job. With a label coverage of 300 square feet per gallon, the same floor needs 1.33 gallons for one coat.
A deck with a railing and steps
Take a floor of 12 by 10 feet, a railing 20 feet long and 3 feet high, and three steps that are 4 feet wide with a run of 1 foot and a rise of half a foot. The floor is 120 square feet and the railing is 60. The steps are 3 x 4 x (1 + 0.5) = 18 square feet, so the total is 198 square feet. One coat takes 198 divided by 175 = 1.131 gallons, and two coats take 2.263 gallons. This example is our own working.
How rough is the railing figure?
The railing area, the length times the height, is a rough estimate, because the real surface of the posts, the rails and the balusters depends on the design. This tool keeps to the simple length times height figure. For an ornate railing, add a margin to the result or measure the separate parts yourself.
What the steps figure leaves out
The steps formula covers the tread and the riser of each step and nothing else. The sides of the steps and the stringers, which are the boards that carry the stairs, are not counted. If your steps are open at the sides or have thick stringers, raise the area a little or measure those faces yourself. The tool treats every step as the same width, and the number of steps must be a whole number.
Coverage depends on the wood and the product
Sherwin-Williams ties its coverage figure to the wood type [1], and the brand and kind of stain change it too. The default of 175 square feet per gallon is a planning figure, not a rule, so use the coverage printed on your can when you have it. In metric mode the default is the same figure converted exactly, which is 4.295 square metres per litre, and the box takes your own figure in square metres per litre.
Pails and leftovers
With the default coverage, a 5 gallon pail covers 5 x 175 = 875 square feet, which is our own arithmetic, and the tool shows the same for your own coverage. In metric mode with the default, a 5 US gallon pail of 18.93 litres covers 81.29 square metres. The buy line rounds up to the next quarter gallon in US mode and the next half litre in metric mode, which is our own rule. Leaving 24 hours between coats is the advice on the Sherwin-Williams page [1], and a little stain left over is useful for touching up later.
Using the calculator and its limits
Measure the floor, the railing and the steps with a tape, and use one unit throughout. The tool gives an estimate for planning. It does not cover cleaning, sanding or sealing. Treat the default of 175 as a cautious rule of thumb and the label of your stain as the better guide.
Common mistakes
- Forgetting a second coat. Enter the number of coats so that the amount is multiplied.
- Ignoring the label. Type the coverage printed on your can, since the default is only a starting figure.
- Counting only the floor. Railings and steps add area, so fill them in unless you will leave them unstained.
- Mixing units. Use feet in US mode and metres in metric mode.
What next
Use this often? Add Deck Stain to your Home screen.
Frequently asked questions
What is a deck stain calculator?
A tool that turns the floor, railing and step areas of a deck into the stain needed, using the coverage per gallon and the number of coats.
How much stain do I need for a 20 by 20 deck?
The floor is 400 square feet. At 175 square feet per gallon, one coat needs 2.29 gallons and two coats need 4.57 gallons.
How many square feet does a gallon of deck stain cover?
Sherwin-Williams says about 250 to 350 square feet a gallon depending on the wood. The tool defaults to a cautious 175, and the label on your stain may give a different figure, so type it in.
Does the calculator count the railing and the steps?
Yes, when you fill in their boxes. The railing is length times height and the steps are number times width times run plus rise.
How do I find the stain for two coats?
Enter 2 in the coats box. The amount is multiplied by the number of coats.
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.