A crude protein calculator converts the nitrogen found in a food or feed into crude protein by multiplying by a conversion factor, usually 6.25. Enter the nitrogen as a percentage, or the grams of nitrogen and the sample mass, choose the food, and it gives the crude protein. It can also work back from protein to nitrogen.
How to use the crude protein calculator
- Choose what you know and the food type.
- Enter the nitrogen and, if needed, the sample mass.
- Press Calculate.
How crude protein is defined
Total nitrogen is measured by the Kjeldahl or Dumas method and multiplied by a factor that depends on the protein expected, and the result is called crude protein [1]. Fat, carbohydrate and fibre contain no nitrogen, so protein is the main source of nitrogen in most foods [1]. The measurement does not identify protein itself, only the nitrogen.
Why 6.25
Food labels use nitrogen multiplied by 6.25 because the average nitrogen content of proteins is about 16 percent [1]. Since 100 divided by 16 is 6.25, each gram of nitrogen stands for 6.25 grams of protein. The Kjeldahl page notes that in practice 6.25 is used for almost all food and feed whether or not it applies, and that US labelling requires it unless another factor has been published [2].
Other factors
The Kjeldahl page lists factors from the FAO: 6.25 for meat, eggs, maize and sorghum; 6.38 for milk; 5.95 for rice; 5.70 for wheat flour; 5.83 for whole wheat and most grains such as barley, oats, rye and millets; 5.71 for soybean and 5.46 for peanuts [2]. The calculator offers these as choices and lets you type another factor. A lower factor reflects proteins that are richer in nitrogen.
Worked examples
A meat sample with 2.5 percent nitrogen has 2.5 × 6.25 = 15.6 percent crude protein. Milk with 0.5 percent nitrogen gives 0.5 × 6.38 = 3.19 percent. Wheat flour with 2.0 percent nitrogen gives 2.0 × 5.70 = 11.4 percent, while the whole-kernel factor of 5.83 would give 11.66. These are our own calculations with the factors above.
From grams of nitrogen
If the laboratory reports the grams of nitrogen found in a weighed sample, use the second mode. Dividing the nitrogen by the sample mass gives the percentage, and the factor does the rest. A 10-gram sample that contains 0.4 grams of nitrogen is 4 percent nitrogen, which is 25 percent crude protein at 6.25. This arithmetic is our own working.
Limits of the method
The page explains that nitrogen cannot tell true protein from non-protein nitrogen, which is found in milk, fish and edible insects [1]. It can also be fooled: urea or ammonium nitrate can inflate the result, and melamine, a nitrogen-rich chemical, was added to milk and pet food in scandals in 2007 and 2008 [1]. The Kjeldahl method does not measure nitro groups or ring nitrogen such as pyridine [2]. Some countries use true protein tests for dairy [1].
Using the result
Crude protein is the figure on feed tags and food labels, and it is how many feeds are priced. For a human diet, remember that protein quality, such as digestibility and amino acid balance, is a separate matter, as the page on protein notes [1]. The calculator gives the standard figure, and for any decision about nutrition you should also look at quality.
How the laboratory test works
In the Kjeldahl method the sample is digested in hot acid, which converts organic nitrogen to ammonium. The ammonia is then distilled and measured by titration, and the nitrogen is calculated from the amount of acid used. The Dumas method burns the sample and measures the nitrogen gas that is released. Either way the answer is a nitrogen percentage, and the factor turns it into crude protein.
Moisture basis
Protein figures can be quoted as received, on a dry matter basis or at a stated moisture. A feed with 10 percent crude protein as received and 12 percent moisture has about 11.4 percent on a dry basis. Check which basis a label or a laboratory report uses before comparing two numbers, because the difference can be large for wet feeds.
Choosing the factor
If you are unsure, use 6.25, which is the convention on labels. Use a food-specific factor when you want a closer estimate of the true protein in a single type of food, and say which factor you used when you report the result.
Example for a feed label
A laboratory reports 3.2 percent nitrogen in a sample of soybean meal. With the soybean factor of 5.71 the crude protein is 18.3 percent, while the label convention of 6.25 gives 20 percent. The gap of nearly two points shows why you should always say which factor was used when comparing two products.
Going backwards
The third mode starts from a protein figure on a label and gives the nitrogen it implies, by dividing by the factor. It is useful for checking whether a reported protein value is consistent with a nitrogen result from a laboratory.
Common mistakes
- Applying 6.25 to every food. Use the factor that matches the food, or state 6.25 as a convention.
- Confusing nitrogen and protein. Protein is nitrogen times the factor.
- Mixing percent and grams. Pick the mode that matches your data.
- Treating crude protein as true protein. It includes non-protein nitrogen.
What next
Use this often? Add Crude Protei to your Home screen.
Frequently asked questions
What is a crude protein calculator?
A tool that converts the nitrogen content of a food or feed to crude protein using a conversion factor.
What is the formula for crude protein?
Crude protein = nitrogen × 6.25 for most foods.
Why is 6.25 used?
Proteins average about 16 percent nitrogen, and 100 ÷ 16 = 6.25.
Which factor is used for milk?
6.38. Wheat flour uses 5.70, rice 5.95 and soybean 5.71.
Is crude protein the same as true protein?
No. It counts all nitrogen, including non-protein nitrogen, so it can overstate protein.
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.