A chemical name calculator names an ionic compound from its two ions. Pick the positive ion, the cation, and the negative ion, the anion, from the lists. You get the name, the formula, the number of each ion and the steps of the naming rule, including the Roman numeral for a metal that has more than one charge.
How to use the chemical name calculator
- Pick the cation from the first list.
- Pick the anion from the second list.
- Press Name it and read the name, the formula and the working.
The three naming rules
Wikipedia's article on chemical nomenclature gives the rules for simple ionic compounds [1]. The cation comes first and keeps the name of its element, so calcium stays calcium and NH₄ is ammonium. A single-atom anion takes the element name with the ending changed to -ide, so chlorine becomes chloride. A cation that can have several charges gets its charge as a Roman numeral in brackets after the name, so FeCl₃ is iron(III) chloride [1]. The calculator applies these rules to your picks.
Ionic compounds
An ionic compound is made of positive and negative ions. In its name the cation comes first, and a metal with several possible charges is named by the Stock system, with a Roman numeral [2]. The formula is deduced from the charges on the ions, with the requirement that the whole compound is neutral [2]. The calculator is limited to such compounds, because the pick-lists contain only ions.
Worked examples
Four examples show the rules, worked by us. The Na⁺ and Cl⁻ ions give NaCl, sodium chloride. Mn²⁺ with Br⁻ gives MnBr₂, manganese(II) bromide, while Mn³⁺ with Br⁻ gives MnBr₃, manganese(III) bromide. Ba²⁺ with CO₃²⁻ gives BaCO₃, barium carbonate. The calculator gives the same names and formulas for these four pairs, with the working shown.
From charges to a formula
The formula needs the smallest whole numbers of the two ions that make the total charge zero. Divide each charge by the greatest common divisor of the two to get the counts, crossing over: the cation count is the anion charge, and the anion count is the cation charge. This procedure is our own working. It gives MgCl₂ for Mg²⁺ and Cl⁻, Na₂SO₄ for Na⁺ and SO₄²⁻, and Fe₂(SO₄)₃ for Fe³⁺ and SO₄²⁻, all examples that Wikipedia uses [2].
Brackets in formulas
When more than one polyatomic ion is needed, its formula goes in brackets before the number, as in Fe₂(SO₄)₃ and (NH₄)₂SO₄. A single-atom ion never needs brackets, so aluminium oxide is Al₂O₃. The bracket rule is the usual convention in chemistry, and it is applied in the tool without a source of its own. The subscripts shown are the counts of each ion.
Roman numerals
Iron can form Fe²⁺ and Fe³⁺, so the name has to say which. FeSO₄ is iron(II) sulfate [2], while Fe₂(SO₄)₃ is iron(III) sulfate. The numeral is the charge of the metal ion. Wikipedia notes that IUPAC prefers charge numbers such as iron(2+) to Roman numerals [2]. The calculator follows the Stock system and uses Roman numerals, and it does not give the old names ending in -ous and -ic.
The ion lists
The lists hold common monatomic cations, some metals with several charges, ammonium, the halides, oxide, sulfide and nitride, and common polyatomic anions such as hydroxide, nitrate, sulfate, phosphate and carbonate. Polyatomic ions are a well known group [3], but their table could not be read in full, so the lists, the names and the charges here are our own selection.
Bicarbonate and hydrogen carbonate
NaHCO₃ is widely called sodium bicarbonate, which is an older name. A tool that follows the rules names the HCO₃⁻ ion hydrogen carbonate, so it gives sodium hydrogen carbonate. We made this choice because the rule-based name is the one that can be derived from the ion. Similar choices apply to hydrogen sulfate and dihydrogen phosphate.
Mercury and the special case
Mercury(I) is Hg₂²⁺, an ion made of two mercury atoms, each with a charge of 1 plus. The list gives it as a polyatomic cation, so mercury(I) chloride is Hg₂Cl₂. The single ion Hg²⁺ is mercury(II). This entry is our own addition to the list, and the Roman numeral is the charge of each atom, not of the whole ion.
What is not covered
Covalent compounds named with prefixes such as di- and tri-, acids, hydrates and organic compounds are outside the scope, and so are formulas typed by hand. If you need to balance a reaction or find a molar mass after naming a compound, use the related tools, which take a formula.
Checking the answer
Check a result by adding up the charges. The total positive charge must equal the total negative charge, and the calculator shows both sums. For aluminum oxide, 2 ions of Al³⁺ give 6 plus, and 3 ions of O²⁻ give 6 minus, so Al₂O₃ is neutral. If the two sums do not match, the formula is wrong, even if the name looks right.
Common mistakes
- Forgetting the Roman numeral. Iron, copper and tin need one.
- Writing the charges instead of the counts. Subscripts are counts.
- Dropping the brackets. Use them for two or more polyatomic ions.
- Applying the rules to covalent compounds. They use prefixes instead.
What next
Use this often? Add Chemical Nam to your Home screen.
Frequently asked questions
What is a chemical name calculator?
A tool that names an ionic compound and writes its formula from a cation and an anion.
How do I name an ionic compound?
Write the cation first with its element name, then the anion, with the ending -ide for a single atom, and add a Roman numeral if the metal has several charges.
When is a Roman numeral needed?
When the metal can form more than one ion, such as iron, copper or manganese, so that the name states its charge.
How is the formula worked out?
From the charges, with the smallest numbers of ions that make the total charge zero.
Does it name covalent compounds?
No. It covers ionic compounds made from the listed ions only.
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.