A car crash force calculator finds the average force and the deceleration in a crash from the mass, the speed and the stopping distance or time. It shows how much a longer stopping distance, such as a crumple zone, reduces the force. It is an educational estimate for an idealized stop, and not a safety assessment.
How to use the car crash force calculator
- Choose US or metric units and what you know.
- Enter the mass, the speed and the distance or time.
- Press Calculate.
Impulse and momentum
The impulse J of a force is the change of momentum, J = p_f − p_i [2]. For a constant force acting for a time Δt, J = F Δt, and for a constant mass, J = m v₂ − m v₁ [2]. So the average force that stops a mass m from a speed v in a time Δt is F = m v ÷ Δt. This rearrangement is our own, and it is the formula of the time mode.
Using the distance
If you know the distance in which the body stops, the page on g-force gives the acceleration when speeding up from rest as a = v² ÷ (2s) [1], and the same holds for slowing down to rest. The force is then F = m a, by Newton's second law [1]. The stopping time follows as t = 2s ÷ v. The calculator uses these in its distance mode.
A worked example
A person of 80 kilograms in a car that hits a barrier at 50 kilometres per hour, which is 13.89 metres per second, and stops in 0.6 metres, has an average deceleration of 160.75 metres per second squared, or 16.4 g. The average force is 12.86 kilonewtons and the stop takes 86.4 milliseconds. These are our own calculations from the formulas.
The crumple zone
The force is inversely proportional to the stopping distance. Doubling the distance from 0.6 to 1.2 metres halves the force and the g-force. This is why cars have crumple zones, and why airbags and seat belts spread the stop over a longer distance. In the example, stopping in only 0.1 metres would give 98 g, far above what a person can survive for long.
Speed matters most
The deceleration grows with the square of the speed for a given distance. Doubling the speed to 100 kilometres per hour, with the same 0.6 metres, gives four times the g-force, 65.6 g. This is a good reason to slow down. The calculator lets you try a few speeds to see how quickly the numbers climb.
What people can survive
The page on g-force says that people can take as much as 20 g for less than 10 seconds in the horizontal direction, and that John Stapp survived a peak of 46.2 g in a sled test [1]. The highest g-force survived in a crash on record is 214 g [1]. These cases were with special restraints and short durations. The calculator notes when the average is above 20 g.
Average and peak
The result is the average over the whole stop. The force in a real crash varies, and it rises to a peak that is often 1.5 to 2 times the average, a rough factor of our own, depending on how the structure collapses. The calculation also treats the person as rigidly attached to the car, with the same stopping distance, which is true only with a good restraint.
US units
In US mode, enter the mass in pounds, the speed in miles per hour and the distance in feet. A person of 176 pounds in a car at 31 miles per hour that stops in 2 feet has a deceleration of 16.06 g and an average force of 12.58 kilonewtons. The calculator converts to SI units and gives the force in pounds-force too.
Limits
This is an educational estimate. It does not include rebound, rotation, the direction of the impact or the effects of different restraints. The injury risk depends on many things that are not in the formula, such as the part of the body and the way the force is spread. It cannot be used to judge a real crash or the design of a vehicle.
Using the calculator
Pick the units. Enter the mass, the speed and either the distance or the time. Read the deceleration in g and the force, and the note. Try longer distances to see how a crumple zone or an airbag helps, and higher speeds to see how the force grows. Remember that the numbers are an average for an idealized stop.
Doubling the distance
For the same 80 kilogram person at 50 kilometres per hour, a stopping distance of 1.2 metres gives 8.2 g and 6.43 kilonewtons, half of the values for 0.6 metres. The relation is simple, so longer stopping distances are always better, as far as the vehicle allows. This is our own calculation, and you can reproduce it by changing the distance in the calculator.
Common mistakes
- Using the average as the peak. Peaks are higher.
- Entering the speed in the wrong unit. Check mph or km/h.
- Forgetting the stopping distance. It sets the force.
- Using it to judge a real crash. It is educational.
What next
Use this often? Add Car Crash Fo to your Home screen.
Frequently asked questions
What is a car crash force calculator?
A tool that estimates the average force of an idealized crash.
How is the average crash force found?
F = m v ÷ Δt, or F = m v² ÷ (2s) from the stopping distance.
Why do crumple zones help?
They lengthen the stopping distance, which lowers the force in proportion.
What happens if the speed doubles?
For the same distance, the deceleration and the force are four times as large.
Is the result the peak force?
No. It is the average over the stop; the peak is higher.
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.