This bike gear calculator works out how big or small a bicycle gear is, from the chainring and cog teeth and the wheel size. It gives gear inches, gear ratio, metres of development and gain ratio, and, if you enter a cadence, your speed in that gear. Use the bike gear calculator to compare gears, choose a cassette or plan a single-speed setup.
How to use the bike gear calculator
- Choose US or metric units. US (inches and mph) is the default.
- Enter the teeth on the front chainring and the rear cog.
- Enter the wheel diameter including the tire.
- Add crank length and cadence if you want the gain ratio and speed, then press Calculate.
Gear inches, development and gain ratio
The Wikipedia article on bicycle gearing describes three common ways to measure a gear. All three start from the gear ratio, the chainring teeth divided by the cog teeth:
- Gear inches = wheel diameter in inches × chainring teeth ÷ cog teeth
- Metres of development = wheel circumference in metres × chainring teeth ÷ cog teeth
- Gain ratio = wheel radius ÷ crank length × chainring teeth ÷ cog teeth (both lengths in the same unit)
Gear inches is the diameter of a wheel that would travel as far for each turn of the pedals if it were driven directly. Development is the distance the bike moves for one full turn of the cranks. Gain ratio also takes crank length into account, so it compares how far the bike moves with how far your feet move. Wikipedia notes that to turn gear inches into metres of development you multiply by about 0.08 (exactly 0.0254 × π).
Wheel size
The calculator needs the wheel's diameter including the tire. According to Wikipedia, a 700c road wheel has a 622 mm rim, and the full diameter is about the rim diameter plus twice the tire width. With 25 mm tires, that's 622 + 50 = 672 mm, or about 26.5 inches. Road bike wheels are usually around 670 mm. For other wheel sizes, check the rim size printed on the tire, or measure the wheel.
Speed at a cadence
If you enter a cadence, the number of times you turn the pedals each minute, the calculator multiplies the development by the cadence and by 60 to get the distance per hour, and shows it in mph or km/h. This is the speed you'd ride in that gear at that cadence, without coasting.
Worked example
Take a road bike with a 53-tooth chainring and a 19-tooth cog, with 672 mm wheels (26.5 inches) and 170 mm cranks. The gear ratio is 53 ÷ 19 = 2.79. That gives 73.8 gear inches and a development of 5.89 metres per pedal turn. The gain ratio is 336 ÷ 170 × 2.79 = 5.5. At a cadence of 90 rpm, that's 5.89 × 90 × 60 = about 31.8 km/h, or 19.8 mph.
Wikipedia points out that 53/19 and 39/14 are almost exactly the same gear, since both ratios are about 2.79. Different combinations can give the same result, which is why riders compare gears by gear inches or development instead of tooth counts.
Typical gear ranges
Wikipedia gives some useful reference points. Single-speed bikes for adults typically have a gear between 55 and 75 gear inches. For racing bikes, a typical lowest gear is around 45 gear inches, or about 35 gear inches with a compact crankset. A very low gear of around 16 gear inches gives a speed of about 3 mph. Moving between cogs changes the gear in steps: swapping a 13-tooth cog for a 15-tooth cog makes the gear about 15.4% lower.
Reading the results
The big number is gear inches. The table shows the gear ratio, the development in metres per pedal turn, the gain ratio (if you entered a crank length) and the speed at your cadence (if you entered one).
Comparing low and high gears
Try your easiest and hardest gears to see your bike's range. On the same 672 mm wheels, a 34-tooth chainring with a 28-tooth cog is about 32 gear inches, a low gear for steep climbs, while a 50-tooth chainring with an 11-tooth cog is about 120 gear inches, a high gear for fast descents. The ratio between them shows how wide the range is.
How crank length affects gain ratio
Gear inches and development only depend on the wheel and the teeth, but gain ratio also uses crank length. Longer cranks give a slightly lower gain ratio for the same gear, because your feet travel further on each turn. In the 53/19 example, 170 mm cranks give a gain ratio of 5.5, and 175 mm cranks would give about 5.4.
Common mistakes
- Using the rim size alone. Add the tire to get the full wheel diameter.
- Swapping front and rear. The chainring is at the front, the cog at the back.
- Mixing units. Choose metric before entering millimetres.
- Comparing tooth counts directly. Compare gear inches instead.
Tips
- Work out your easiest and hardest gears to see your range.
- Use gear inches to compare bikes with different wheel sizes.
- Try a few cadences to find a comfortable speed for each gear.
What next
Use this often? Add Bike Gear to your Home screen.
Frequently asked questions
How does a bike gear calculator work?
It divides chainring teeth by cog teeth and multiplies by the wheel size to give gear inches and metres of development.
How do you calculate gear inches?
Gear inches = wheel diameter in inches × chainring teeth ÷ cog teeth.
What is metres of development?
The distance the bike moves for one full turn of the pedals: wheel circumference × chainring ÷ cog.
What size is a 700c wheel?
The rim is 622 mm; add twice the tire width, so about 672 mm (26.5 in) with 25 mm tires.
What is a good single-speed gear?
Wikipedia says single-speed bikes for adults typically have a gear between 55 and 75 gear inches.
Sources
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.