A bike frame size calculator gives you a starting point when you are choosing a new bicycle. Enter your inseam, and this bike frame size calculator suggests a frame size for a road bike, a mountain bike and a hybrid. If you don't have an inseam measurement, it can estimate one from your height. Getting the frame size roughly right makes a bike more comfortable, easier to control and safer to ride, so it is worth taking a couple of minutes to measure yourself properly before you buy.
Bike frame size formulas
- Road bike: inseam (cm) × 0.67
- Mountain bike: inseam (cm) × 0.66, usually converted to inches
- Hybrid bike: inseam (cm) × 0.685
These multipliers are our own working starting points: we found no official standard for inseam-based sizing, and guides use different figures, particularly for mountain and hybrid bikes. That is why the number should be treated as a guide rather than a final answer.
How to use the bike frame size calculator
- Choose your bike type and your units.
- Measure your inseam and enter it.
- Or enter your height if you can't measure your inseam right now.
- Press Calculate to see the suggested size, along with the figures for the other kinds of bike.
How to measure your inseam
Your inseam is the distance from the floor to your crotch. Stand barefoot or in socks with your back against a wall and your feet slightly apart. Pull a large book up firmly between your legs, keeping its spine level, as a saddle would press. Then measure from the top of the book down to the floor. Take the measurement twice and use the average. Asking a friend to hold the tape and to mark the wall makes this far more accurate.
Bike frame size example
If your inseam is 80 cm, a road frame comes out at 80 × 0.67 = 53.6 cm. A mountain bike frame is 80 × 0.66 = 52.8 cm, which is about 20.8 inches. A hybrid is 80 × 0.685 = 54.8 cm. You would then look for the frame nearest to this figure in the maker's size chart.
Why inseam beats height
Two riders of the same height can have legs of quite different lengths. Using height alone ignores that difference, and the difference is exactly what determines your standover clearance and saddle height. When you only enter your height, this calculator estimates your inseam as about 46.8 percent of your height, our own working that reflects an average body shape rather than your own. The result is shown with a note, so that you know it is less reliable. Measure your inseam whenever you can.
How frames are measured
Frame size was traditionally measured along the seat tube from the center of the bottom bracket to the very top of the seat tube, and many bikes are now measured to the intersection of the top tube and seat tube centerlines. [2] The measuring point is not standardized, so two bikes with the same nominal size can differ by about 2 cm. [2] Many modern frames also use letter sizes such as S, M and L. Road frames are usually labelled in centimeters, and mountain bike frames in inches. Since these conventions differ between manufacturers, two bikes with the same number may fit differently, so always check the brand's own size chart.
Between two sizes?
If you fall between two sizes, think about how you like to ride. A smaller frame generally feels more nimble and easier to handle, while a larger frame tends to feel more stable and stretched out. Riders with long arms and a short torso may suit one size differently from others of the same height. If at all possible, take a test ride, and pay attention to your comfort, your reach to the handlebars and how much clearance you have when you stand over the frame.
Fine-tuning your fit
Frame size is only the first step. Saddle height, saddle position, stem length and handlebar width can all be adjusted to suit you. A good bike shop will set these for you, and serious riders may benefit from a professional bike fit. If you feel pain in your knees, back or hands, the fit probably needs adjusting. Children need a different approach, since kids' bikes are normally sized by wheel diameter rather than frame size.
Buying a bike online
If you can't try the bike before buying, take extra care with the measurements. Compare the suggested size with the geometry table for the exact model, and look at the standover height in particular, which is the distance from the ground to the top of the frame at the point where your crotch is when you straddle the bike. [1] A common rule of thumb is an inch or two between the top tube and your body. [2] Check the returns policy before you order, in case the size turns out to be wrong. Keep the packaging until you are sure that the bike fits.
Common mistakes
- Using height alone. Leg length varies a lot.
- Measuring with shoes on. Measure in socks or bare feet.
- Assuming all brands match. Check the size chart of the specific bike.
- Skipping the test ride. Nothing beats trying the bike.
Related tools
Convert your measurements with the length converter, plan your journey time with the driving time calculator, and track your energy with the calorie calculator.
What next
Use this often? Add Bike Frame S to your Home screen.
Frequently asked questions
How does the bike frame size calculator work?
It multiplies your inseam by a factor for the type of bike: 0.67 for road, 0.66 for mountain and 0.685 for hybrid.
What size bike do I need for an 80 cm inseam?
About a 53.6 cm road frame, a 20.8-inch mountain frame or a 54.8 cm hybrid frame.
Can I use my height instead of my inseam?
Yes, but it is less accurate because leg length varies. The calculator estimates your inseam from your height.
Are all bike sizes the same across brands?
No. Brands measure and size frames differently, so check the maker's chart.
What if I am between two sizes?
A smaller frame usually feels nimbler, and a larger frame more stable. A test ride is the best way to decide.
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.