Saved

Press the star next to a tool's name to save it.

All my tools

Belt Size Calculator

Use this belt size calculator to find your belt size from your trouser size or a waist measurement, in inches or centimeters, for regular or low-rise trousers, with the letter size from S to XXXL.

Restored your last values ·

From a trouser size, add 2 inches; for jeans or low-rise trousers add a further 3 or 4 inches. A tape measurement where you wear the belt is the belt size itself.

Everything is worked out in your browser. Nothing you type is sent anywhere.

Your belt size

–

Enter your size, then press Calculate.

See full result

This belt size calculator works out the belt size to buy from your trouser size or your waist measurement. Enter your size in inches or centimeters, say whether your trousers are regular rise or jeans and low-rise, and the belt size calculator gives your belt size in inches and centimeters, plus the letter size from a typical S to XXXL chart.

How to use the belt size calculator

  1. Choose inches or centimeters.
  2. Pick what you know: your trouser size, or a tape measurement around your waist where you wear your belt.
  3. Enter the size, and choose regular or low-rise for trousers.
  4. Press Calculate.

The 2-inch rule

The general rule for belt size is to take your trouser size and add 2 inches. If you wear size 34 trousers, choose a size 36 belt. The aim is for the belt to fit on its middle hole: that leaves room to tighten it or let it out as your body changes, or for different clothes, such as a shirt tucked in or left loose, or light trousers versus heavier fabrics.

Jeans and low-rise trousers

Jeans and low-rise trousers sit lower on your hips, where you're usually wider, so they need a longer belt. For these, add a further 3 or 4 inches on top of the usual 2, so size 34 jeans take a belt of about 39 to 40 inches. The calculator gives that range when you choose jeans or low-rise.

Measuring your waist

If you're not sure of your trouser size, or your trousers are labelled with a letter size, measure instead. Wrap a tape measure around your waist at the height at which you'll wear the belt, and note where it meets once around. That number is where the centre hole of the belt should fit, so it's your belt size: don't add 2 inches to a tape measurement. Choose "waist measured with a tape" and enter it.

Belt size chart

Trouser sizeBelt sizeLetter size
30 in32 in (81 cm)Small
32 in34 in (86 cm)Medium
34 in36 in (91 cm)Medium
36 in38 in (97 cm)Large
38 in40 in (102 cm)Extra large
40 in42 in (107 cm)Extra large
42 in44 in (112 cm)XXL

Letter sizes follow one maker's chart: small belts run 31 to 33 inches, medium 34 to 36, large 37 to 39, extra large 40 to 42, XXL 43 to 45 and XXXL 46 to 48. Each range runs from the tightest to the loosest the belt can be worn, which is why different brands' letter sizes can overlap.

Reading the letter sizes

Belts sold as small, medium or large cover a range of waists rather than one exact size. A medium on the chart used here fits waists of 32 to 34 inches, 81 to 86 centimeters, as a belt of 34 to 36 inches, 86 to 91 centimeters. Because each range runs from the tightest to the loosest the belt can be worn, someone at the top of one range may prefer the next size up so the belt fits on its middle hole. If your result falls between two letter sizes, check the maker's own chart.

When to size up

The calculator's results are a starting point. If you often wear your belt with heavier trousers or tuck in a thick shirt, a little more length gives room to fasten it on the middle hole. The same applies if your trousers sit lower than their size suggests. When in doubt between two sizes, the longer belt can be fastened a hole tighter, while a belt that's too short can't be made longer.

Worked examples

Say you wear size 34 trousers. Adding 2 inches gives a 36-inch belt, 91 centimeters, a medium. If they're low-rise jeans, add a further 3 to 4 inches for a belt of 39 to 40 inches. If you measured 37 inches around your waist with a tape where you wear your belt, a 37-inch belt, a large, is the one to buy.

Centimeter sizes

Belts sold in Europe are often sized in centimeters. Choose Metric and enter your trouser size or waist measurement in centimeters: the calculator converts at 2.54 centimeters to the inch, applies the same rule and shows the result in both units, so you can compare it with any size chart. For example, trousers with an 86 centimeter waist take a belt of about 91 centimeters, and a waist you measured at 94 centimeters with a tape takes a 94 centimeter belt. Round to the nearest size the shop sells, and if you're between two sizes, pick the longer one so the belt still reaches the middle hole when you wear thicker clothes.

Common mistakes

  • Buying your trouser size. It'll fit on the last hole, or not at all.
  • Adding 2 inches to a tape measurement. The measurement already is the belt size.
  • Forgetting the rise. Low-rise jeans need a longer belt.
  • Ignoring the middle hole. A good fit sits on the centre hole, not the first or last.

Tips

  • Compare with an old belt that fits you well.
  • Check the brand's chart, as letter sizes vary.
  • Pick a belt with five holes so the middle one fits.

What next

Use this often? Add Belt Size to your Home screen.

Frequently asked questions

What size belt should I get?

Take your trouser size and add 2 inches: size 34 trousers take a 36-inch belt.

How does the belt size calculator handle jeans?

For jeans or low-rise trousers it adds a further 3 to 4 inches, so size 34 jeans take about a 39 to 40 inch belt.

Do I add 2 inches to my waist measurement?

No. A tape measurement where you wear the belt is already your belt size.

What letter size is a 36-inch belt?

Medium, on a chart where medium covers 34 to 36 inches.

Can I use centimeters?

Yes. Choose Metric to enter and see sizes in centimeters.

What went wrong?

We only receive the reason you pick, never what you typed into the tool.

Thanks for your feedback.

More Everyday Life Tools