Saved

Press the star next to a tool's name to save it.

All my tools

Wedge Volume Calculator

This wedge volume calculator gives the volume and surface area of a wedge with a rectangular base. Enter the base length, base width, height and the length of the top edge, and it works out the rest in one click.

Restored your last values ·

Enter the base length (a), base width (b), height (h) and the apex edge (c). Leave the apex edge blank for a wedge that ends in a sharp edge.

Everything is worked out in your browser. Nothing you type is sent anywhere.

–

–

Enter the wedge sizes to see its volume and surface area.

See full result

What this wedge volume calculator does

A wedge is a solid with five faces, nine edges and six vertices. [1] Think of a doorstop, a chisel tip or a ramp seen as a solid block. This wedge volume calculator takes the size of the rectangular base, the height of the top edge above the base and the length of that top edge. It then returns the volume, the total surface area and the area of each group of faces.

The page uses one specific wedge, so it helps to say which. The base is a rectangle that is a long and b wide. The top edge, called the apex edge, has length c and runs parallel to side a. It sits directly above the middle of the base at height h. That gives two sloping trapezoid faces along the long sides and two sloping triangle faces at the ends.

How to use the wedge calculator

  1. Type the base length a and the base width b. These are the two sides of the rectangle the wedge sits on.
  2. Type the height h, measured straight up from the base to the apex edge.
  3. Type the apex edge c. Leave it blank if the wedge ends in a sharp line, which is the same as c = 0.
  4. Press Calculate. The volume, surface area and a breakdown of the faces appear.

Every box uses the same unit. If you measure in centimetres, the volume is in cubic centimetres and the surface area is in square centimetres. Convert first if your measurements come in mixed units.

The volume formula

The volume of a wedge with a base of a by b, a top edge of c and a height of h is given on the Wikipedia page for wedges as V = b × h × (a/3 + c/6). [1] That page prints the formula without clear fraction marks, so we read it this way and checked it against the special cases below. The formula can also be written V = b × h × (2a + c) / 6.

Two special cases show the formula is sensible. When c = a, the top edge is as long as the base and the wedge is a right triangular prism. The formula then gives V = b × h × a / 2, which is half of the box a × b × h, exactly what a prism with a triangular end must give. When c = 0 the solid becomes a pyramid-like chisel and the volume is b × h × a / 3, one third of the box.

The surface area formula

The Wikipedia page does not give a surface area formula, so the figures below are our own working from the geometry of the shape described above. [1] The surface is made of four sloping faces and the rectangular base.

  • Base: a × b.
  • Two trapezoid sides, each with parallel edges a and c and a slant height of √(h² + (b/2)²). Their combined area is (a + c) × √(h² + (b/2)²).
  • Two triangle ends, each with base b and a slant height of √(h² + ((a − c)/2)²). Their combined area is b × √(h² + ((a − c)/2)²).
  • Total: the base plus the trapezoids plus the triangles.

These slant heights are found with the Pythagorean theorem. The top edge sits over the middle of the base, so the horizontal run from the base edge up to the apex is b/2 on the long sides and (a − c)/2 at the ends.

Worked example

Take a wedge with a base of 6 by 4, a top edge of 2 and a height of 3, all in centimetres.

StepWorkingResult
Volume4 × 3 × (6/3 + 2/6)28 cm³
Base6 × 424 cm²
Trapezoid slant height√(3² + 2²)3.6056 cm
Two trapezoids(6 + 2) × 3.605628.844 cm²
Two triangles4 × √(3² + 2²)14.422 cm²
Total surface area24 + 28.844 + 14.42267.266 cm²

Enter 6, 4, 3 and 2 in the calculator and you get the same volume of 28 and a surface area of 67.266.

Where wedge volume is useful

  • Estimating the material in a concrete or gravel wedge, such as a tapered footing or a ramp edge.
  • Working out how much wood or foam a doorstop, shim or cutting block needs.
  • Checking a CAD sketch or a school geometry problem for a solid with two triangle faces and two trapezoid faces.
  • Finding the soil in a cut or fill that slopes on all four sides.

Tips and common mistakes

  • Do not mix units. A base in feet with a height in inches gives a wrong answer.
  • Height means the straight vertical distance, not the length of the sloping face.
  • The apex edge cannot be longer than the base length a. If it is, the calculator reports an error because the shape would no longer be this kind of wedge.
  • A right triangular ramp, where one end is a full vertical wall, is a different solid. For that shape use half of a rectangular box: length × width × height ÷ 2, which is what you get here by setting c equal to a.
  • The surface area includes the base. Subtract it if you only need the outside sloped faces.

How accurate is it

The calculation is exact for the shape described. Real wedges are rarely perfect, so add a small margin for waste when ordering material, and measure the actual dimensions rather than relying on a drawing. Results are shown to six significant figures.

What next

Use this often? Add Wedge Volume to your Home screen.

Frequently asked questions

What is the wedge volume formula?

For a base of a by b, an apex edge of c and a height of h, the volume is b × h × (a/3 + c/6). For example, a base of 6 by 4, a top edge of 2 and a height of 3 gives a volume of 28.

How does the wedge volume calculator treat a triangular prism?

If you set the apex edge equal to the base length, the wedge becomes a right triangular prism and the volume is half of the surrounding box, a × b × h ÷ 2.

What if my wedge ends in a sharp edge?

Leave the apex edge blank or enter 0. The volume then becomes one third of the box, b × h × a ÷ 3.

Does the calculator include the base in the surface area?

Yes. The total is the base, two trapezoid sides and two triangle ends. The breakdown line shows each part so you can leave the base out if you wish.

Which units can I use?

Any unit, as long as every box uses the same one. The answer is in cubic units for volume and square units for surface area.

What went wrong?

We only receive the reason you pick, never what you typed into the tool.

Thanks for your feedback.

More Math Tools