Saved

Press the star next to a tool's name to save it.

All my tools

Water Density and Viscosity Calculator

Use this water density calculator to find the density and the dynamic and kinematic viscosity of pure water at any temperature between freezing and boiling.

Restored your last values ·

Choose US or metric units and enter the temperature of pure liquid water, from freezing to boiling. You get the density and the dynamic and kinematic viscosity.

Everything is worked out in your browser. Nothing you type is sent anywhere.

–

–

Enter the water temperature, then press Calculate.

See full result

A water density calculator gives the density of pure liquid water at any temperature from freezing to boiling. The same page also works as a water viscosity calculator: it shows the dynamic viscosity in millipascal seconds and the kinematic viscosity in square millimetres per second. Enter the temperature in degrees Fahrenheit or Celsius.

How to use the water density calculator

  1. Choose US or metric units.
  2. Enter the water temperature between freezing and boiling.
  3. Press Calculate.
  4. Read the density and the viscosity.

How density changes with temperature

Water is densest at about 4 degrees Celsius. Wikipedia puts the peak density at 3.98 degrees Celsius [1], and its data page tabulates the density of liquid water from 0 to 100 degrees [2]. Warmer water is lighter, which is why hot water rises in a tank. The tool covers the same 0 to 100 degree range.

The density formula

The tool approximates the density of pure water with a fifth-order polynomial in the temperature T in degrees Celsius. The density in kilograms per cubic metre is 999.83311, plus 0.0752 T, minus 0.0089 T squared, plus 7.36413 × 10⁻⁵ T cubed, minus 4.74639 × 10⁻⁷ T to the fourth, plus 1.34888 × 10⁻⁹ T to the fifth. The tool uses these coefficients exactly.

A worked example

At 20 degrees Celsius, which is 68 degrees Fahrenheit, the polynomial gives about 998.295 kilograms per cubic metre, or 0.998295 grams per cubic centimetre. At 100 degrees it gives about 958.02. The Wikipedia data page lists 998.21 at 20 degrees and 958.35 at 100 degrees [2], so the polynomial agrees with the tabulated values to within 0.04 percent. The pure-water figures here are our own working from the polynomial.

Density in other units

One gram per cubic centimetre equals 1,000 kilograms per cubic metre, and one pound per cubic foot is about 16.018 kilograms per cubic metre. The tool therefore shows the density in kg per cubic metre, in g per cubic centimetre and in pounds per cubic foot, dividing by 16.018463. At 20 degrees that is about 62.32 pounds per cubic foot.

Dynamic viscosity

Dynamic viscosity measures how much water resists flow. Wikipedia gives a semi-empirical Vogel–Fulcher–Tammann equation for water: the viscosity equals 0.02939 millipascal seconds times e to the power 507.88 divided by (T − 149.3), with T in kelvin [3]. At 20 degrees it gives about 1.004 millipascal seconds, and at 25 degrees about 0.8913. Wikipedia lists 1.0016 for 20 degrees and says about 0.89 at 25 degrees [3].

Checking the viscosity against a table

The Wikipedia data page gives a table of values, for example 1.7921 millipascal seconds at 0 degrees, 1.0050 at 20 degrees and 0.2838 at 100 degrees [2]. The equation gives 1.775, 1.004 and 0.2841, within about 1 percent. The tool follows the equation, not the table.

Kinematic viscosity

Kinematic viscosity is the dynamic viscosity divided by the density. Wikipedia defines it as ν = η ÷ ρ [3]. With η in millipascal seconds and ρ in grams per cubic centimetre, ν comes out in square millimetres per second. At 20 degrees the tool gives about 1.005 mm²/s, close to the 1.007 that the tabulated viscosity and density give [2]. It is the figure used in flow and pipe calculations.

Temperature range

The tabulated data on the Wikipedia data page run from 0 to 100 degrees [2], and Wikipedia states no range for its viscosity equation [3]. The tool is therefore limited to 0 to 100 degrees Celsius, or 32 to 212 degrees Fahrenheit. Outside this range, such as for steam or deep-frozen ice, you need other data.

Salt water and pressure

Wikipedia says that the density of salt water depends on the dissolved salt content as well as the temperature [1]. This tool has no formula for the salt and pressure terms. For that reason this calculator covers only pure water at normal pressure. Seawater is denser, so use a seawater tool for the sea.

Where the values are used

Density is used to turn a volume of water into a mass, and the viscosity decides how easily water flows through pipes, pumps and nozzles. A cup of hot tap water weighs a little less than a cup of cold water. The same inputs also answer the usual questions about water density at 20 or 25 degrees, and the viscosity of water at room temperature.

Reading the results

The first result gives the density in kilograms per cubic metre together with the temperature in both scales, so you can check that the units were read as you meant. The second line gives grams per cubic centimetre and pounds per cubic foot. The viscosity lines give the dynamic value, which equals centipoise, and the kinematic value. Between 0 and 100 degrees the density falls by about 4 percent while the viscosity falls by a factor of more than six, which is why hot water flows so much more easily. Remember that these are values for clean liquid water at normal pressure, so tap water, seawater and mixtures will differ a little, and check any critical design figure against a handbook table.

Weighing a tank of water

Density turns a volume into a mass. In our own example, take a 200 litre tank, which is 0.2 cubic metres. At 20 °C the density is about 998.295 kilograms per cubic metre, so the water weighs 0.2 × 998.295 = 199.66 kilograms. At 60 °C the polynomial gives about 983.11 kilograms per cubic metre, so the same tank holds 196.62 kilograms.

The difference is about 3.0 kilograms, or 1.5 percent. A heated tank does not lose water. The same mass simply takes up more room, so a fixed volume holds less. Use this idea when you size a hot water tank or convert a measured volume to a weight, and remember that the figures are for pure water.

Common mistakes

  • Using the values for salt water. Salt raises the density.
  • Entering a temperature outside the range. The tool covers 0 to 100 degrees Celsius.
  • Mixing dynamic and kinematic viscosity. Kinematic is dynamic divided by density.
  • Mixing the temperature units. Check the US or metric choice.

What next

Use this often? Add Water Densit to your Home screen.

Frequently asked questions

What is a water density calculator?

A tool that gives the density of pure liquid water from its temperature, here with the viscosity as well.

What is the density of water at 20 degrees Celsius?

About 998.3 kilograms per cubic metre, or 0.9983 grams per cubic centimetre.

At what temperature is water densest?

At about 4 degrees Celsius, near 3.98.

What is the viscosity of water at room temperature?

About 1.0 millipascal seconds at 20 degrees and about 0.89 at 25 degrees.

Does the calculator work for salt water?

No. It covers pure liquid water, and salt and pressure change the density.

What went wrong?

We only receive the reason you pick, never what you typed into the tool.

Thanks for your feedback.

More Unit Converters