Saved

Press the star next to a tool's name to save it.

All my tools

Vertical Exaggeration Calculator

Use this vertical exaggeration calculator to find VE from horizontal and vertical map scales, such as 1:24,000 and 1:2,400, and to convert slope angles on an exaggerated profile.

Restored your last values ·

Enter the horizontal and vertical scales of a profile or relief map, as the N in 1 : N, to get the vertical exaggeration. Or enter what one unit of drawing stands for in each direction. Two more modes convert slope angles between the exaggerated and the true profile.

Everything is worked out in your browser. Nothing you type is sent anywhere.

–

–

Choose what to work out, fill in the boxes, then press Calculate.

See full result

A vertical exaggeration calculator finds how much taller the vertical scale of a map, cross section or profile is than its horizontal scale. Enter the two scales, for example 1 : 24,000 horizontally and 1 : 2,400 vertically, and it gives the vertical exaggeration, 10×. It also converts slope angles between an exaggerated profile and the real ground.

How to use the vertical exaggeration calculator

  1. Choose from the scales and enter the horizontal and vertical scale denominators, the N in 1 : N.
  2. Or choose from what one unit stands for and enter, for example, how many metres 1 centimetre stands for in each direction.
  3. Press Calculate. Use the two angle modes to convert slopes.

What vertical exaggeration is

The Wikipedia article on vertical exaggeration says that it is a scale used in raised-relief maps, plans and technical drawings such as cross sections, to emphasise vertical features that might be too small to identify relative to the horizontal scale.[1] It is given as a number: 5× means that vertical measurements appear 5 times greater than horizontal ones.[1]

The formula

The page gives VE = VS ÷ HS, where VS is the vertical scale and HS is the horizontal scale, both as representative fractions.[1] A scale of 1 : 2,400 is the fraction 1 ÷ 2,400, and 1 : 24,000 is 1 ÷ 24,000, so the ratio is 24,000 ÷ 2,400 = 10. In terms of the denominators, the vertical exaggeration is the horizontal denominator divided by the vertical denominator. The calculator shows this working.

The worked example from the page

The page says that if 1 centimetre vertically represents 200 metres and 1 centimetre horizontally represents 4,000 metres, the vertical exaggeration is 20×.[1] Enter 200 and 4,000 in the second mode and the calculator gives 20×. Check the working in terms of representative fractions: 1 cm for 200 m is 1 : 20,000 vertically, and 1 cm for 4,000 m is 1 : 400,000 horizontally, and 400,000 ÷ 20,000 = 20. This check is our own.

No exaggeration, and below 1

The page says that a value of 1× means that the horizontal and vertical scales are identical, which is regarded as no vertical exaggeration.[1] Values below 1 are not common, but would indicate a reduction in the vertical scale, or equivalently a horizontal exaggeration.[1] The calculator describes each case in words after the number.

The effect on slopes

The page does not say how exaggeration changes slopes, so this section is our own geometry. If a profile is drawn with a vertical exaggeration VE, every slope on the drawing is VE times the real slope. So the true angle is the arctangent of the tangent of the drawn angle divided by VE, and the drawn angle is the arctangent of the tangent of the true angle times VE. A 45 degree slope on a drawing with 10× exaggeration is really only 5.71 degrees, and a real slope of 5.71 degrees is drawn at 45 degrees. The calculator has a mode for each direction.

Why and when to exaggerate

Many landscapes are very flat compared with their width, so a profile drawn at true scale shows almost no relief. Exaggerating the vertical scale makes hills and valleys visible. The page also records the criticism that some scientists object to vertical exaggeration as a tool that makes an oblique view dramatic at the cost of misleading the viewer about the true appearance of the landscape, and that too high a value can confuse the map reader.[1] State the exaggeration on every profile that uses it, as a number such as 10×, so that readers can allow for it.

Units

Both scales must be in the same units before you divide. Representative fractions such as 1 : 24,000 are unitless, so they are safe. If you enter what one centimetre stands for, give both values in the same unit, such as metres. A mix of metres and kilometres will give a wrong answer by a factor of a thousand. The page notes only the unitless fractions.[1]

Drawing a profile with a chosen exaggeration

To draw a cross section, pick the horizontal scale first, usually the scale of your map, and then choose a vertical scale that makes the relief visible. If the map is 1 : 50,000 and the relief is a few hundred metres, a vertical scale of 1 : 5,000 gives 10× and a vertical scale of 1 : 10,000 gives 5×. Divide the horizontal denominator by the exaggeration you want to find the vertical denominator. For 1 : 50,000 and a 5× exaggeration this is 50,000 ÷ 5 = 10,000. This is our own method from the formula above.

Reading the result in a report

When you publish a profile, give the vertical exaggeration beside the scale bar, for example VE = 10×. If a figure has no stated exaggeration, readers may take the slopes at face value and overstate them. The same applies to three-dimensional views of terrain, where a stated exaggeration lets the reader judge how steep the real ground is. The page's criticism is a reminder to use only as much exaggeration as the purpose needs.{1}

Some quick checks

A profile that shows a gentle 3 degree slope with a vertical exaggeration of 5 corresponds to a real slope of about 0.6 degrees, which is almost flat. A real slope of 10 degrees drawn at 4× appears to be about 35 degrees, which looks steep. These conversions are our own arithmetic from the angle rule above.

Common mistakes

  • Dividing the wrong way round. VE is the horizontal denominator divided by the vertical denominator.
  • Reading slopes straight from the drawing. Divide the tangent by VE first.
  • Mixing units. Use the same unit in both directions.

What next

Use this often? Add Vertical Exa to your Home screen.

Frequently asked questions

What is a vertical exaggeration calculator?

A tool that finds how much a profile or relief map stretches vertical features compared with horizontal distances, from the two scales.

What is the formula for vertical exaggeration?

VE = VS ÷ HS, the vertical scale divided by the horizontal scale, both as representative fractions.

What does 5× vertical exaggeration mean?

Vertical measurements appear 5 times greater than horizontal ones.

How do I find the true slope from an exaggerated profile?

Divide the tangent of the drawn angle by VE and take the arctangent. A 45 degree slope at 10× is really 5.71 degrees.

What does a vertical exaggeration of 1 mean?

The horizontal and vertical scales are the same, so there is no vertical exaggeration.

What went wrong?

We only receive the reason you pick, never what you typed into the tool.

Thanks for your feedback.

More Math Tools