Saved

Press the star next to a tool's name to save it.

All my tools

Vertical Curve Calculator

Use this vertical curve calculator to work out the BVC, EVC, high or low point, K value and elevation at any station on a parabolic road vertical curve.

Restored your last values ·

Grades are in percent: use a minus sign for downhill. Stations are distances along the road, written as plain numbers (1000 for 10+00).

Everything is worked out in your browser. Nothing you type is sent anywhere.

–

Enter the grades, curve length and PVI, then press Calculate.

See full result

This vertical curve calculator works out the elevations along a parabolic vertical curve on a road or path profile. Enter the grade in and out, the curve length and the station and elevation of the point of vertical intersection (PVI), and the vertical curve calculator gives the start and end of the curve, the high or low point, the K value and the elevation at any station you choose.

How to use the vertical curve calculator

  1. Choose US or metric units. US (feet) is the default.
  2. Enter the initial grade g1 and final grade g2 in percent, with a minus sign for downhill.
  3. Enter the curve length and the PVI station and elevation.
  4. Enter a station to check its elevation, if you like, then press Calculate.

What is a vertical curve?

According to Wikipedia's article on the geometric design of roads, a road's profile is made of slopes, called grades, connected by parabolic vertical curves. Vertical curves give a gradual change from one grade to another, so vehicles can pass smoothly over the change. A crest curve, where the final grade is lower than the initial one, appears as a hill; a sag curve, where the final grade is higher, appears as a valley. The article uses BVC and EVC for the beginning and end of the curve, PVI for the point where the two grades meet, A for the difference in grades and L for the curve length measured horizontally.

The vertical curve formulas

A symmetrical vertical curve is a parabola centered on the PVI, starting L ÷ 2 before it and ending L ÷ 2 after it. With x the horizontal distance from the BVC:

  • BVC elevation = PVI elevation − g1 × L ÷ 200
  • Elevation at x = BVC elevation + g1 × x ÷ 100 + (g2 − g1) × x² ÷ (200 × L)
  • High or low point at x = −g1 × L ÷ (g2 − g1), when it falls on the curve
  • K = L ÷ A, the length of curve for each 1% change in grade

As the Wikipedia article describes, the curve elevation is the tangent elevation, along the initial grade, minus the offset, which grows with the square of the distance from the BVC.

Worked example

A crest curve joins a +2% grade to a −3% grade over 400 feet, with the PVI at station 1000 (10+00) and elevation 500 feet. The BVC is at station 800, elevation 500 − 2 × 400 ÷ 200 = 496 feet, and the EVC at station 1200, elevation 494 feet. A = 5%, so K = 400 ÷ 5 = 80. The high point is 2 × 400 ÷ 5 = 160 feet from the BVC, at station 960, elevation 497.6 feet. At the PVI station, the curve is 2.5 feet below the PVI, at 497.5 feet.

A sag curve from −4% to +2% over 600 feet with the PVI at station 2000, elevation 300, has its low point at station 2100, elevation 304 feet.

Reading the results

The big number is the elevation at the station you entered, or the high or low point if you didn't enter one. The table shows the curve type, the BVC and EVC stations and elevations, the high or low point, A, K and the offset at the middle of the curve.

Why K matters

K tells you how gradual the curve is: a larger K means a longer, gentler curve for the same change in grade. The Wikipedia article notes that design guidelines take into account speed, vehicle type, grade, view obstructions and stopping distance, and that for sag curves the most important design factor is the headlight sight distance at night, which must be long enough for a driver to see an obstruction and stop.

Checking points along the curve

Enter any station between the BVC and EVC to get the elevation of the curve there. In the crest example, station 900, 100 feet from the BVC, is at 496 + 2 × 100 ÷ 100 − 5 × 100² ÷ 80,000 = 497.375 feet, and station 1100, 300 feet from the BVC, is at 502 − 5.625 = 496.375 feet. Checking points every 25 or 50 feet is a common way to set out the curve on site or to check a design profile.

When there's no high or low point

A curve only has a high or low point within its length when the grades have opposite signs, uphill into downhill or the reverse. If both grades are uphill, for example from +2% to +6%, the curve keeps rising, and its lowest point is simply the BVC. The calculator shows the high or low point only when it falls between the BVC and EVC.

Metric profiles

Choose metric to enter lengths, stations and elevations in meters. The grades stay in percent, and the formulas are the same. A 120-meter curve from +2% to −3% with the PVI at 150 meters elevation has its BVC 1.2 meters below the PVI and a K value of 24.

Common mistakes

  • Forgetting the minus sign. Downhill grades are negative.
  • Using decimals for grades. Enter 2 for 2%, not 0.02.
  • Measuring L along the road. L is the horizontal length.
  • Checking a station off the curve. Stations must lie between the BVC and EVC.

Tips

  • Write stations as plain numbers, 1000 for 10+00.
  • Check a few points against your drawings.
  • Use design standards for minimum curve lengths.

What next

Use this often? Add Vertical Cur to your Home screen.

Frequently asked questions

How does a vertical curve calculator work?

It treats the curve as a parabola centered on the PVI: elevation = BVC elevation + g1·x/100 + (g2 − g1)·x²/(200L).

How do you find the high point of a vertical curve?

At x = −g1 × L ÷ (g2 − g1) from the BVC, when that falls on the curve.

What is K on a vertical curve?

The curve length divided by the change in grade, A: K = L ÷ A.

What is the difference between a crest and a sag curve?

A crest curve's final grade is lower than its initial grade, forming a hill; a sag curve's is higher, forming a valley.

What do BVC, EVC and PVI mean?

Beginning of vertical curve, end of vertical curve and point of vertical intersection of the two grades.

What went wrong?

We only receive the reason you pick, never what you typed into the tool.

Thanks for your feedback.

More Math Tools