A spiral length calculator works out how long a flat spiral is, from its inner and outer radius and the number of turns or the gap between them. It uses the exact formula for an Archimedean spiral, in which each turn is the same distance from the last. A second mode estimates the length of a coil of rope, tape, hose or cable from its thickness. It runs in your browser.
How to use the spiral length calculator
- Choose what you know: the number of turns, the gap between turns or the thickness of a coil.
- Enter the inner and the outer radius.
- Enter the turns or the gap.
- Press Calculate.
The Archimedean spiral
The Wikipedia article on the Archimedean spiral describes it in polar coordinates (r, θ) by the equation r = bθ, and notes that its polar form can also be written r = (v ÷ ω)θ + c, for a point moving away from the center at a constant speed while it turns at a constant rate.[1] The page says that any ray from the origin meets successive turns at a constant separation distance, equal to 2πb if θ is measured in radians.[1] So the gap between turns is 2πb. Given the gap and the inner and outer radius, the calculator finds b = gap ÷ 2π, and the angles at the start and the end of the spiral, θ = r ÷ b.
The length formula
The page gives the length of the arc from θ = 0 to θ as (b ÷ 2)[θ√(1 + θ²) + ln(θ + √(1 + θ²))], or, equivalently, (b ÷ 2)[θ√(1 + θ²) + arsinh θ].[1] For a spiral that starts away from the center, subtract the length up to the starting angle from the length up to the ending angle. The Spiral article gives the general arc-length integral for a polar curve, L = ∫√(r′² + r²) dφ, and the Archimedean formula above is its closed form.[2] For b = 1 and one turn, from θ = 0 to 2π, the length is about 21.26, compared with 39.48 for a full circle at the end radius, because the spiral winds out gradually from the center.
Number of turns and gap
If you know the inner radius r₀, the outer radius r₁ and the number of turns n, the gap is (r₁ − r₀) ÷ n. Equivalently, if you know the gap, the number of turns is (r₁ − r₀) ÷ gap. The calculator uses whichever you give, and shows the other. For a spiral from r₀ = 0 to r₁ = 2π with a gap of 2π, there is exactly one turn.
Coils of rope, tape and hose
For a coil of material that is wound flat, such as a rope on a drum, a roll of tape or a garden hose on a reel, you usually know the thickness t of the material, which is the gap between turns, and the inner and outer radius of the coil. A good estimate of its length is the area of the ring divided by the thickness, π(r₁² − r₀²) ÷ t, since the material fills that area. This is the standard approximation and it is not written on the pages. The calculator also shows the exact Archimedean length for the same gap, and the two agree closely when the coil has many turns. A 0.1 m thick hose coiled from a radius of 1 m to 3 m has about 251.3 m of hose, in 20 turns.
The average-radius shortcut
A quick estimate multiplies the circumference at the average radius by the number of turns: 2π × (r₀ + r₁) ÷ 2 × n. For the hose above, the average radius is 2 m, and 2π × 2 × 20 is 251.3 m, the same as the area method. For a spiral with few turns, the estimates differ from the exact formula, which is why the exact value is shown first. The average radius method is close to the exact answer when the gap is small compared with the radii.
Examples in design
The spiral length is useful for estimating the cable on a reel, the groove on a record, the wire in a coil or the tube in a heating coil, for the length of a spiral path in a garden or a labyrinth, and for the tape on a roll. Try your own numbers and compare the three results to see how good the estimates are.
Tips for accurate results
Measure the radii to the center line of the material when you can, since the formulas follow the center line of the coil. For a tightly wound coil, the number of turns can be counted along a radius, or worked out from the thickness. If the coil is not flat, but wound in layers on a drum, use the circumference of each layer instead. The calculator is for spirals in a plane, in which each turn lies outside the last.
Common mistakes
- Using the diameter instead of the radius. The formulas need radii.
- Mixing units. Give all the lengths in the same unit.
- Using the thickness of the roll instead of the material. The gap is the thickness of the material, not of the whole roll.
- Applying the formula to a spiral with a growing gap. The Archimedean spiral has a constant gap.
What next
Use this often? Add Spiral Lengt to your Home screen.
Frequently asked questions
What is a spiral length calculator?
A tool that finds the length of a flat spiral from its radii and the number of turns or the gap between them, and the length of a coil of material.
What is the formula for an Archimedean spiral?
In polar form r = bθ, with a gap of 2πb between turns. The length from 0 to θ is (b ÷ 2)[θ√(1 + θ²) + arsinh θ].
How do I find the length of a roll of tape or rope?
Divide the area of the ring, π(R² − r²), by the thickness of the material. For a thickness of 0.1, radii 1 and 3 give about 251.3.
What is the gap between turns?
2πb for r = bθ. It is the distance between neighboring turns along any ray from the center.
Is the average-radius estimate accurate?
It is close when the gap is small compared with the radii. The exact formula is better for spirals with few turns.
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.