A snowman calculator finds the sizes, volumes and weights of the three balls of a snowman. Enter the diameter of the bottom ball, choose the proportions and the snow density, and you get the middle and top balls and the total snow.
How to use the snowman calculator
- Choose US or metric units.
- Pick the proportions of the three balls, 3 : 5 : 8 or 1 : 2 : 3.
- Enter the diameter of the bottom ball.
- Change the snow density if you wish, and press Calculate.
What this calculator does
This is a deliberately simple tool. It treats the snowman as three spheres stacked on each other, finds their sizes from the proportions, and works out the volume of each from the formula for a sphere. Then it multiplies by a snow density to get a weight. It does not model how fast a snowman melts, and we do not claim to. Everything about the arithmetic is our own working, as explained below.
Three balls
According to Wikipedia, a snowman is typically built from three spheres of snow in North America, while two are used in the United Kingdom [2]. The page does not give sizes or proportions for the spheres [2]. This calculator therefore uses three balls, and it asks you for the size of the bottom one. Each ball above it is smaller, in a fixed proportion that you choose.
The proportions
You can choose 3 : 5 : 8, or 1 : 2 : 3, for the top, middle and bottom balls. No page that we read gives standard proportions for the balls of a snowman, so we chose the two proportions ourselves as the options. With 3 : 5 : 8 and a bottom ball of 80 cm, the middle ball is 80 × 5 ÷ 8 = 50 cm and the top ball is 80 × 3 ÷ 8 = 30 cm.
Volume of a sphere
The volume of each ball is 4/3 × π × r³, where r is the radius, which is half of the diameter. This is the standard formula for the volume of a sphere [3]. For the ball of 80 cm the radius is 40 cm and the volume is 268,083 cubic centimetres. The middle ball of 50 cm has 65,450 cubic centimetres and the top ball of 30 cm has 14,137 cubic centimetres.
Snow density
Wikipedia says that the density of seasonal snowpack is approximately 30 percent of the density of water, and that in late spring it can rise to as much as 50 percent [1]. We use 30 percent as the default, and you can change it. The weight of a ball is its volume multiplied by the density, with water at 1 gram per cubic centimetre, or 1,000 kilograms per cubic metre, which is again our own working.
Packed snow is denser
The 30 percent figure is for the snowpack that lies on the ground. Snow that is rolled and pressed into a ball may well be denser than that, so you may wish to try a higher value. That is our own caution, and the pages that we read give no figure for snow that is packed in this way. For this reason the density is an input and not a fixed number in the calculator.
A worked example
For the 3 : 5 : 8 proportions and a bottom ball of 80 cm, the three volumes add up to 347,670 cubic centimetres, which is about 0.348 cubic metres, or 348 litres. At a density of 30 percent, that weighs about 104.3 kilograms. The bottom ball has 77 percent of the snow, the middle one has 19 percent and the top one has 4 percent. These are our own figures.
Height
The height shown is the sum of the three diameters, which is what you would get if the balls just touched at single points. That is 160 cm for the example. A real snowman is a little shorter, because each ball sinks into the one below it, and the head may be placed on top with some overlap. It is our own simplification, but it is a good guide when you need to know if the figure fits under a roof or a branch.
Why there is no melting model
No page that we read gives a melting rate for a snowman. A melting time would have depended on the temperature, the sun, the wind and the snow itself, and we would have had to invent the figures. We have therefore left it out, and we say so rather than show a number that has no source behind it.
Using the result
Use the volumes to judge how much snow you need to gather, and the weights to see whether you can lift the top ball. As a rough guide, the weight shows why most people roll the bottom ball on the ground and lift only the lighter balls. Try a larger or smaller bottom ball and compare the two proportions, to find a snowman that suits your garden and your strength.
Common mistakes
- Entering the radius. The calculator wants the diameter of the bottom ball, which is twice the radius.
- Forgetting that snow density varies. Change the percentage for wet or packed snow.
- Expecting a melting time. This calculator gives no melting estimate.
- Mixing the units. Use inches in US mode and centimetres in metric mode.
What next
Use this often? Add Snowman to your Home screen.
Frequently asked questions
What is a snowman calculator?
A tool that finds the sizes, volumes and weights of the three balls of a snowman from the size of the bottom ball.
What are the proportions of a snowman?
This calculator offers 3 : 5 : 8 or 1 : 2 : 3 for the top, middle and bottom balls.
How much does a snowman weigh?
The volume of the three spheres times the snow density. An 80 cm bottom ball with 3 : 5 : 8 gives about 348 litres and 104 kilograms at 30 percent.
What is the density of snow?
Wikipedia gives approximately 30 percent of the density of water for seasonal snowpack, and up to 50 percent in late spring.
Does it say how long a snowman lasts?
No. There is no melting model, because no page we read states one.
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.