Saved

Press the star next to a tool's name to save it.

All my tools

Scuba Weight Calculator

Use this scuba weight calculator to adjust the lead from your buoyancy check for fresh or salt water, and see how much the gas in a full tank weighs. An estimate only.

Restored your last values ·

ft³
L
bar

Do a buoyancy check first, in shallow fresh water, with a nearly empty tank and an empty BCD, and note the lead that makes you float at eye level. Enter that, your body weight with all equipment but no lead, and the water you will dive in. You get the adjusted ballast for the new water and the weight of the gas in your tank.

Everything is worked out in your browser. Nothing you type is sent anywhere.

–

–

Enter your weight with equipment and the lead from a buoyancy check, then press Calculate.

See full result

A scuba weight calculator helps you adjust the ballast for a dive. Instead of guessing a weight from your body, it starts from the lead that you found in a buoyancy check, and adds the extra push of denser water. It also shows how much the gas in a full tank weighs.

How to use the scuba weight calculator

  1. Do a buoyancy check and enter the lead you needed.
  2. Enter your body weight with all equipment, but without the lead.
  3. Choose fresh or salt water.
  4. Optionally enter the tank size and press Calculate.

Why weighting matters

A diver must be weighted enough to be slightly negatively buoyant at the end of the dive, when the tank is nearly empty. The Wikipedia page says the weight normally lies between 2 kilograms and 15 kilograms, and that buoyancy and weighting problems have been implicated in a relatively high proportion of scuba diving fatalities [1]. For that reason this page treats the result as an adjustment of a checked value, not as a prescription.

The buoyancy check

The practical method is a buoyancy check. The page describes it as done with the tank nearly empty and the buoyancy compensator empty, in shallow water, adding or removing weight until the diver is neutrally buoyant [1]. If your dive centre has a pool, do the check there, and ask a dive professional, especially as a beginner. The calculator needs the result of such a check.

Fresh water and salt water

Wikipedia gives an average surface sea water density of about 1,025 kg/m³, and pure water is about 1,000 [2]. The tool rounds sea water to 1,030 as its own planning figure, a little above the surface average. By Archimedes' principle, the push on a body equals the weight of the water it displaces [3], so the same diver is pushed up by 3 percent more in salt water. This is our own working from those two numbers. The Wikipedia page notes that with the air exhaled most people sink in fresh water, and with full lungs most float in seawater [1].

The formula

If you are neutral in fresh water with a total mass M, which is your body and equipment plus the lead, then the volume you displace is M divided by 1,000 cubic metres per tonne. In salt water that volume pushes up M × (1,030 ÷ 1,000 − 1) = 0.03 × M more. The extra lead is 0.03 × M, and the answer is your checked lead plus that amount, plus any change you enter. This is the textbook buoyancy calculation, and it is our own working.

A worked example

Take a diver of 85 kilograms with all equipment, who needed 4 kilograms in a fresh-water check. The total is 89 kilograms, and 0.03 × 89 is 2.67 kilograms. The estimate for salt water is 4 + 2.67 = 6.67, about 6.7 kilograms. In pounds, 187 pounds with a check of 9 pounds gives a total of 196, an extra 5.88 and about 14.9 pounds in salt water. These are our own example figures, not from either page.

The change box

The change box lets you add or remove weight for something that differs from the check. The Wikipedia page says that the weight needed depends on the diver's mass and body composition, the buoyancy of the gear, the salinity of the water, the gas used and the water temperature [1]. We have no sourced figure for the buoyancy of each wetsuit, so you must find that from your own check. Enter a positive number for more lead, and a negative number for less.

Weight of the gas

A full tank is heavier than an empty one. The Wikipedia page gives the air density as about 1.2 kilograms per cubic metre, and says that a common 80 cubic foot tank, 11 litres at 207 bar, holds about 6 pounds, or 2.7 kilograms, of air [1]. The calculator uses the same rule: 11 × 207 litres is 2.277 cubic metres, and times 1.2 is 2.73 kilograms. You start the dive about that much more negative than you finish.

Tank material

The Wikipedia page says that most steel tanks stay negatively buoyant even when empty, while aluminium tanks may become positively buoyant as the gas is used [1]. The page gives no number that we could use for the buoyancy of an empty tank. If you change tank type, repeat the buoyancy check, and enter the new lead.

What we could not source

We found no source to cite for the buoyancy of each wetsuit or empty tank, or for the density of brackish water, so the tool uses none. Wikipedia presents the buoyancy check as the practical method, and we found no rule there that turns body weight into a belt weight [1]. For this reason the calculator offers only fresh and salt water, and no body-weight rule.

Using the result safely

Treat the number as a starting point for a new check, not as the final weight. Make a small change, test it in shallow water, and distribute the lead for trim. The Wikipedia page advises that enough of the weight is carried so that it can be removed quickly in an emergency [1]. Ask a dive professional if you are unsure, and never dive with a weight that you have not tested.

Common mistakes

  • Using the weight from a salt-water check as the fresh-water value. Enter fresh-water lead only.
  • Forgetting to take the lead out of the body weight. Enter the weight without the lead.
  • Treating the result as a final weight. Check it again in shallow water.
  • Ignoring a change of suit or tank. Repeat the check.

What next

Use this often? Add Scuba Weight to your Home screen.

Frequently asked questions

What is a scuba weight calculator?

A tool that adjusts the lead from a buoyancy check for the water density and shows the weight of the gas in a full tank.

How much more weight does salt water need?

About 3 percent of your total mass, from sea water at 1,030 kilograms per cubic metre against 1,000 for fresh water.

Can it tell me my weight from my body weight?

No. We found no source with such a rule, so the tool starts from a real buoyancy check.

What is a buoyancy check?

A test in shallow water with the tank nearly empty and the BCD empty, adding or removing weight until you are neutral.

Is the result safe to dive with?

Not without checking it. Confirm it in shallow water and with a dive professional.

What went wrong?

We only receive the reason you pick, never what you typed into the tool.

Thanks for your feedback.

More Unit Converters