A roll length calculator finds how long the material is on a roll of paper, tape, foil, film or fabric, from the size of the roll and the thickness of the material. Enter the outer diameter, the inner diameter and the thickness, and the calculator gives the length. It can also work backwards and give the outer diameter for a length. It uses the area of a ring, a standard geometry result.[1] It runs in your browser and nothing you enter is sent anywhere.
How to use the roll length calculator
- Choose US or Metric units and what you want to find.
- Enter the outer diameter of the roll and the inner diameter of the core.
- Enter the thickness of the material.
- Press Work out the roll.
The formula
The length is pi times the outer diameter squared minus the inner diameter squared, divided by 4, then divided by the thickness. In other words, the end of the roll is a ring, and its area is the area of the outer circle minus the area of the inner circle. With outer radius R and inner radius r, that area is pi times R squared minus r squared,[1] and writing each radius as half a diameter gives the form above. If the material is laid down in layers with no gaps, the area of the ring is also the length times the thickness (our own working), so dividing the area by the thickness gives the length. To go the other way, the outer diameter is the square root of 4 times the thickness times the length divided by pi, plus the inner diameter squared.
Worked examples
Here is an example of our own for a roll of tape with an outer diameter of 4.5 inches, a core of 1.6 inches and a thickness of 0.01 inch. The ring area is pi times 20.25 minus 2.56, divided by 4, which is about 13.9 square inches. Dividing by 0.01 gives about 1,390 inches, or about 116 feet of tape. In metric units, a roll of 12 centimetres outside and 4.5 centimetres at the core, with material 0.4 millimetres thick, holds about 24 metres.
Measuring a thin material
If the material is too thin to measure, you can measure a stack of layers and divide by the number of layers. For example, measure 10 sheets of paper and divide the height by 10. Pressing the stack lightly gives a better figure, but do not squash it too much, or the thickness will be too small.
What the formula assumes
The formula rests on several assumptions. It ignores stretching or elasticity of the material, and assumes that there are no gaps when the roll is wound. It assumes that the material goes at least one full turn around the core, and that each layer covers the one below it fully. For this reason it does not apply to thread on a spool, where the turns lie side by side. Real rolls often hold a bit less material than the formula says, because of gaps, and the thickness can change under pressure.
Wallpaper and leftover rolls
Roll sizes differ between countries and makers, so read the length printed on the label rather than relying on a standard. You can use the calculator to check how much of a roll is left, by measuring the diameter of what remains and comparing the result with the label. The same method works for a partly used roll of tape, foil or film.
Reading the result
The calculator shows the length of material in feet for US units and in metres for metric units, or the outer diameter in inches or centimetres when you work backwards. The length is a theoretical figure, so a real roll may be shorter by a few percent. If you need an accurate length, compare the result with a roll of known length of the same material, and adjust the thickness until the two agree.
Finding the thickness from a roll
If you know the length of a roll and its diameters but not the thickness of the material, you can rearrange the formula to find it. The thickness is pi times the outer diameter squared minus the inner diameter squared, divided by 4, divided by the length. This is a quick way to find the thickness of tape, film or paper that is too thin to measure with a ruler. The calculator does not have a mode for this, but the formula is simple enough to do by hand.
Uses
People use roll length to estimate how much tape, wrapping paper, foil, cling film, plastic sheeting, carpet or fabric is left on a roll, and to compare the length in rolls of different sizes. Shops and factories use the same idea to estimate stock without unrolling it. For rolls that are tight or loose, adjust the thickness to match what you measure.
Metric entries
In metric mode, the diameters are in centimetres and the thickness is in millimetres, since the thickness of a thin material is usually quoted in millimetres. The calculator changes the thickness into centimetres before it works out the length, and shows the length in metres. In US mode, all sizes are in inches, and the length is in feet. Make sure that you use the right unit for the thickness, since a mistake of ten times changes the result by ten times.
Common mistakes
- Using the radius. Enter diameters, not radii.
- Mixing the units of the thickness. The thickness is in inches for US units and in millimetres for metric.
- Measuring the roll with the core only partly out. Measure the true inner diameter.
- Applying it to a spool of thread. The turns of thread do not lie in layers.
What next
Use this often? Add Roll Length to your Home screen.
Frequently asked questions
What is a roll length calculator?
A tool that finds the length of material on a roll from its outer and inner diameter and the thickness of the material.
What is the formula for the length of a roll?
L = π (D² − d²) ÷ (4 T), where D is the outer diameter, d the inner diameter and T the thickness.
How do I measure a very thin material?
Measure a stack of N layers and divide by N, for example 10 sheets of paper.
Does it work for thread on a spool?
No. The formula assumes each layer fully covers the previous one.
Can I find the diameter of a roll?
Yes. Choose that mode and enter the length, the core diameter and the thickness.
Sources
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.