A mm to carat converter estimates the weight of a round diamond from its size. Millimetres measure length, not weight, so the estimate uses the average diameter and the total depth. Enter the two measurements and read the weight in carats, grams and milligrams.
How to use the mm to carat converter
- Choose the weight in carats to estimate a weight.
- Enter the average diameter and the total depth in millimetres.
- Add a weight correction in percent if you want one.
- Press Calculate.
The formula
For a round stone, the estimate is the average diameter squared, times the total depth, times 0.0061 [1]. The diameter and the depth are in millimetres and the result is in carats. The factor 0.0061 is a rule of thumb. The trade article says that, with practice, a margin of error of less than three percent is possible [1].
A worked example
Take a round stone 6 millimetres across and 2 millimetres deep. The square of 6 is 36, times 2 is 72, times 0.0061 gives 0.4392 carats, which the tool shows as 0.439 carats. A larger stone of 12.5 millimetres and 2 millimetres deep gives 156.25 times 2 times 0.0061, or 1.906 carats. Both results are our own arithmetic.
Carats, grams and milligrams
One carat is 200 milligrams, which is exactly one fifth of a gram [2]. The tool therefore gives the estimate in all three units. The 0.439 carat stone of the example weighs about 87.8 milligrams, or 0.0878 grams. To change a weight that you know from carats to grams, multiply by 0.2. To change it to milligrams, multiply by 200. The tool does this for you and shows the numbers in the result line.
The average diameter
A round stone is not always perfectly round, and the diameter can differ a little when you measure at different angles. Using the average of the smallest and largest readings is a sensible practice. That is our own suggestion and not a rule from either page. Measure with a gauge in millimetres, and enter the number with decimals, such as 6.45, as the diameter enters the formula as a square.
The total depth
The depth is the total depth of the stone, from the flat top face to the lowest point, measured in millimetres with the same gauge. The weight is proportional to the depth, so a 5 percent error in the depth gives a 5 percent error in the weight. The diameter matters more, because it is squared in the formula. A small error in the diameter makes a larger error in the weight.
The weight correction
The trade article adds a percentage to the weight for the girdle: one to five percent for a slightly thick girdle, three to six percent for a thick one, and as much as five to twelve percent for a very thick to extremely thick one, with the larger percentages for smaller stones [1]. It says that crown angle, crown height and other features may also need weight adjustments, but gives no percentages for them [1]. The correction box is optional and you decide on the value. Leave it blank for 0, and the tool uses a factor of 1.
The girdle factor
Because the correction depends on the thickness of the girdle and on the size of the stone, this tool lets you enter the percentage yourself instead of choosing one for you. With a 5 percent correction the example stone becomes 0.4392 times 1.05, which is 0.461 carats. That is our own arithmetic.
From weight to diameter
You can also choose to find the diameter. Enter the weight in carats and the depth, and the tool solves the formula backwards: the diameter is the square root of the weight divided by the depth, 0.0061 and the correction. This reverse form is our own working and is not on either page. For 0.4392 carats and 2 millimetres, the average diameter is 6 millimetres, which checks the first example.
Other shapes and stones
The formula here is for round brilliant diamonds only. The trade article says that fancy shapes require a different approach [1], so they are not built into this tool. Other gem materials have a different density, so a diamond factor does not suit them. That last point is our own working. Use a tool made for the shape and stone.
How good is the estimate
The article's figure of under three percent error needs practice and careful measurement [1], and we cannot promise it for your stone. Cut proportions, a thick girdle, a high crown and old cuts can move the real weight away from the estimate. Use the result to compare stones or to check a description, and weigh the stone on a scale for an exact value. A jeweller's scale reads the weight directly in carats, and that value always wins over a calculation.
Common mistakes
- Entering the diameter in inches. The formula uses millimetres.
- Using it for a fancy shape. It is for round stones only.
- Treating the result as exact. It is an estimate.
- Forgetting the correction for a thick girdle. Add a percentage if the girdle is thick.
What next
Use this often? Add mm to Carat to your Home screen.
Frequently asked questions
What is a mm to carat converter?
A tool that estimates the weight of a round diamond in carats from its size in millimetres.
What is the mm to carat formula for a round diamond?
Carats equal the average diameter squared, times the depth, times 0.0061, with sizes in millimetres.
How many milligrams are in a carat?
One carat is 200 milligrams, which is 0.2 grams.
What is the weight correction for?
It adds a percentage for a thick girdle. The trade article gives one to five percent for a slightly thick girdle and up to twelve percent for an extremely thick one.
Is the estimate exact?
No. Weigh the stone on a scale for its real weight.
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.