Saved

Press the star next to a tool's name to save it.

All my tools

Mesh to Micron Converter

Use this mesh to micron converter to turn a US standard or Tyler mesh number into its sieve opening in microns, millimeters and inches, or find the nearest mesh for a micron size.

Restored your last values ·

Mesh numbers do not convert with a formula. The converter uses the published table of sieve openings for the series you pick.

Everything is worked out in your browser. Nothing you type is sent anywhere.

Result

–

Enter a number and press Calculate.

See full result

This mesh to micron converter turns a mesh number into the size of the sieve opening in microns (micrometers), millimeters and inches, and turns a size in microns into the nearest mesh. Pick the US standard or the Tyler series, choose the direction and enter a number. Mesh 100 on the US scale is a 150 micron opening, and mesh 200 is 75 microns.

Mesh is a measurement of particle size, often used to determine how a granular material is distributed by size. A higher mesh number means finer openings, so finer particles pass through it.

How to use the mesh to micron converter

  1. Choose US or metric units for the inch or millimeter row.
  2. Choose the US standard or the Tyler mesh series.
  3. Choose mesh to micron, or micron to mesh.
  4. Enter the number and press Calculate.

What mesh means

Many mesh sizes were historically given as the number of holes per inch. Because the wire has width, the mesh number does not equal a fraction of an inch, and several systems give slightly different sizes for the same number. Wikipedia notes that several standardized series exist. That is why a simple formula such as 25,400 divided by the mesh number gives only a rough guess, and why the converter uses the published table of sieve openings.

How a sieve test works

Wikipedia's example is a sample from a truckload of peanuts placed on a mesh with 5 mm openings. When the mesh is shaken, small broken pieces and dust pass through while whole peanuts stay on top, and a buyer can judge whether a batch has too many broken pieces. Standardized mesh series were created to make this kind of testing uniform from one laboratory to the next. In the same way, a stack of sieves of decreasing opening can sort a sample into size fractions that you weigh to find the distribution.

Microns, millimeters and inches

A micron is another name for a micrometer, one thousandth of a millimeter. One millimeter is 1,000 microns and about 0.0394 inch, and one inch is 25,400 microns. The converter shows the opening in microns first because that is how fine sieves are specified, and then in inches for US readers or in millimeters for metric readers.

Sizes in the US standard series

Coarse sieves run from mesh 3.5 at 5,600 microns and mesh 4 at 4,750 microns, through mesh 10 at 2,000, mesh 20 at 850 and mesh 40 at 425 microns. Fine sieves include mesh 60 at 250, mesh 80 at 180, mesh 100 at 150, mesh 140 at 105, mesh 200 at 75, mesh 270 at 53, mesh 325 at 44 and mesh 400 at 37 microns. The table also lists mesh 500 at 25, mesh 625 at 20, mesh 800 at 15, mesh 1250 at 10 and mesh 2500 at 5 microns.

Tyler mesh

The Tyler series uses different numbers for some of the same openings. A 1,700 micron opening is mesh 12 on the US scale but mesh 10 on the Tyler scale. A 425 micron opening is mesh 40 US and mesh 35 Tyler. Always check which series your supplier or standard uses before ordering a screen.

Worked examples

A 100 mesh sieve in the US series has an opening of 150 microns, which is 0.15 mm or about 0.0059 inch. A 200 mesh sieve is 75 microns, or 0.0030 inch, and a 325 mesh sieve is 44 microns. A 40 mesh sieve is 425 microns, about 0.0167 inch.

Going the other way, a 100 micron particle falls between mesh 140 (105 microns) and mesh 170 (90 microns). The converter picks the closest listed opening, mesh 140, and shows that it differs by 5 microns. A 500 micron opening is exactly 35 mesh in the US series and 32 mesh in the Tyler series.

When a mesh number is not listed

Only the sizes in the table are standard, so a number like 150 mesh has no standard opening. If you enter one, the converter tells you the two listed numbers either side, such as 140 and 170, instead of guessing.

Where mesh sizes are used

  • Sieving soil, sand, gravel, minerals and powders to see how coarse they are.
  • Choosing screens and filters for food, chemicals, pharmaceuticals and paint.
  • Describing abrasives, ground spices and ground coffee.
  • Specifying particle size for 3D printing powders and metal powders.

Choosing a mesh for sand, soil and powders

Coarse sands and gravels are screened with low mesh numbers, while powders such as flour, cement and ground minerals need the fine, high numbers. When you buy a filter or screen, match the opening to the smallest particle you want to catch. If you want to keep 150 micron particles out of a liquid, a screen with a smaller opening than 150 microns is needed, which means a mesh number above 100. Ask the supplier whether the quoted number is a nominal opening or an absolute rating, because filter ratings can differ from sieve openings.

Tips

  • Say which series you mean, US standard or Tyler.
  • Remember that a finer particle needs a higher mesh number and a smaller micron size.
  • Treat the result as the nominal opening of a new sieve. Real screens vary within tolerance.

To convert other small lengths use the length converter, and for rock and sand quantities see the gravel calculator and the cubic feet to pounds converter.

What next

Use this often? Add Mesh to Micr to your Home screen.

Frequently asked questions

How do you use a mesh to micron converter?

Pick the mesh series, enter the mesh number and read the opening in microns. For example, 100 mesh in the US series is 150 microns.

What is 200 mesh in microns?

A 200 mesh US sieve has an opening of 75 microns, about 0.0030 inch.

What is the difference between US mesh and Tyler mesh?

They use different numbers for some of the same openings. A 425 micron opening is 40 mesh in the US series and 35 mesh in the Tyler series.

Why can't I use a simple formula for mesh to micron?

Mesh numbers count holes per inch, but the wire takes up width, and several systems differ slightly. Published tables are more reliable than dividing 25,400 by the mesh number.

Does a higher mesh number mean finer particles?

Yes. A higher mesh number has smaller openings, so only smaller particles pass through. Mesh 400 is 37 microns and mesh 40 is 425 microns.

What went wrong?

We only receive the reason you pick, never what you typed into the tool.

Thanks for your feedback.

More Unit Converters