This hiking calculator estimates how long a hike will take from its distance and the total height you climb. Choose US or metric units, enter the distance and ascent, and the hiking calculator uses Naismith's rule, the classic rule of thumb for hill walkers, to give the walking time, with options for rough ground and group pace.
How to use the hiking calculator
- Choose US or metric units. US (miles and feet) is the default.
- Choose a pace rule: Naismith for paths and trails, Aitken for rough ground, or Langmuir for a group.
- Enter the distance and the total ascent, the sum of all the climbs on the route.
- Add a start time if you want an estimated finish time, then press Calculate.
Naismith's rule
Naismith's rule dates from 1892. The rule can be stated as:
1 hour for every 3 miles (5 km) of distance, plus 1 hour for every 2,000 feet (600 m) of ascent
The rule assumes hikers of reasonable fitness, on typical terrain, in normal conditions. It doesn't allow for rest stops, meals or time spent finding the way, so those need to be added. The same rule can also be written in other ways, such as 12 minutes per kilometer plus 10 minutes per 100 meters of ascent.
Rough ground and groups
Over the years, hill walkers have suggested changes to Naismith's rule for different conditions. The calculator includes two of them:
- Aitken (1977): 3 miles (5 km) an hour on paths, tracks and roads, but only 2½ miles (4 km) an hour on all other ground, plus the same 1 hour per 2,000 feet (600 m) of ascent.
- Langmuir (1984): for a group, 4 km an hour plus 1 hour for every 450 m of ascent, based on the fitness of the slowest member.
Langmuir also suggested corrections for descents: on gentle slopes between 5 and 12 degrees, subtract 10 minutes for every 300 m of descent; on steep slopes over 12 degrees, add 10 minutes per 300 m. The calculator leaves descent out, since it depends on the slope, but you can add or subtract that time yourself.
How the calculator works
The calculator divides the distance by the walking speed for the rule you choose, divides the ascent by the climbing rate, and adds the two together. In US units, Naismith's rule uses 3 miles an hour and 2,000 feet an hour; in metric, 5 km an hour and 600 m an hour. The two versions are rounded slightly differently, so the same hike can come out a few minutes apart in each. If you enter a start time, the calculator adds the walking time to it.
Worked example
Take a hike of 8 miles with 2,500 feet of total ascent. The distance takes 8 ÷ 3 = 2 hours 40 minutes, and the climbing adds 2,500 ÷ 2,000 = 1 hour 15 minutes, for a total of 3 hours 55 minutes of walking. Starting at 8:30, you'd finish at about 12:25 without breaks.
In metric, a 20 km route with 1,600 m of ascent takes 4 hours for the distance and 2 hours 40 minutes for the climbing, or 6 hours 40 minutes in total. Using Langmuir's group pace, the same route would take about 8 hours 33 minutes.
Equivalent flat distance
Scarf proposed another way to think about the rule, and his analysis of fell running records supports it: every unit of height climbed is worth about 8 units of flat distance. So 1,600 m of climbing is like walking an extra 12.8 km on the flat, and a 20 km route with that climb is about 32.8 km of flat walking. At 5 km an hour, that takes about 6 hours 34 minutes, close to the Naismith estimate.
Reading the results
The big number is the estimated walking time. The table splits it into the time for the distance and the extra time for the climbing, and shows a finish time if you entered a start time. Remember that this is moving time only.
Working out the total ascent
The ascent is the total height you climb over the whole route, not just the height of the summit above the start. On a route that climbs 1,500 feet, drops 500 feet into a valley and then climbs another 1,000 feet, the total ascent is 2,500 feet. Most route-planning maps and apps show the total ascent for a route. If you're reading a paper map, count the contour lines you cross going uphill and multiply by the contour interval.
Adding breaks and a safety margin
Because Naismith's rule leaves out stops, plan your own. A short rest every hour or so and a longer lunch stop can add an hour or more to a full day. Turn the walking time into a day plan by adding your breaks, then add a margin for weather, slower ground or a wrong turn. If you entered a start time, the finish time the calculator shows is the earliest you'd get back without any stops.
Comparing with your own pace
The rule describes an average hiker. Once you've done a few routes, compare your actual walking times with the calculator's estimates. If you're usually faster or slower, you'll know how to adjust its estimates for future hikes.
Common mistakes
- Using the summit height. Enter the total climbing, adding up every uphill section.
- Forgetting breaks. Add time for rests, lunch and photos.
- Using paths pace on rough ground. Choose Aitken for heather, scree or bog.
- Ignoring the slowest walker. Groups move at the pace of their slowest member.
Tips
- Measure distance and ascent from a map or route planner.
- Compare the estimate with your own times on a few hikes, and adjust.
- Plan to finish well before dark, with time to spare.
What next
Use this often? Add Hiking to your Home screen.
Frequently asked questions
How does a hiking calculator work?
It uses Naismith's rule: 1 hour per 3 miles (5 km) of distance plus 1 hour per 2,000 feet (600 m) of ascent.
How long does it take to hike 8 miles with 2,500 feet of climbing?
About 3 hours 55 minutes of walking by Naismith's rule, plus breaks.
Does Naismith's rule include breaks?
No. It covers walking time only, so add time for rests and meals.
How do I adjust for rough ground?
Aitken's version slows the pace to 2½ miles (4 km) an hour away from paths, tracks and roads.
How do I estimate time for a group?
Langmuir suggests 4 km an hour plus 1 hour per 450 m of ascent, based on the slowest member.
Sources
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.