A film calculator converts between the length of motion-picture film, the number of frames and the running time. Choose 35 mm, 16 mm, Super 8 or standard 8 mm, give the frame rate, and enter any one of the length, the running time or the frame count. You get the other two, and the film speed in feet per minute. It is useful for planning a shoot, buying a roll, or checking how long a reel will run. It works in feet or in metres and runs in your browser.
How to use the film calculator
- Choose US (feet) or Metric (metres).
- Pick the film gauge and what you know: the length, the running time or the frames.
- Enter the frame rate, or leave it blank for the usual rate of the gauge.
- Enter the length, the time or the frames, and press Calculate.
The three relations
The calculator uses three simple relations. The number of frames is the length in feet times the frames per foot. The running time in seconds is the number of frames divided by the frame rate. The film speed in feet per minute is the frame rate times 60 divided by the frames per foot. The only figure that depends on the gauge is the number of frames in each foot of film, and the following sections give it for each gauge.
35 mm
The Wikipedia article on 35 mm movie film says that the film has 4 perforations per frame, along both edges, and that there are 16 frames per foot.[1] At the sound speed of 24 frames per second, the film runs through the projector at 16 frames per foot ÷ 24 frames per second, which is 90 feet per minute, a figure that we worked out from the two numbers. A roll of 1,000 feet has 16,000 frames and runs for 666.7 seconds, which is 11 minutes and 6.7 seconds at 24 frames per second. The calculator shows this as 11:06.7.
16 mm
The article on 16 mm film gives the pitch of the frames as 7.62 mm (0.300 inch) for print and reversal film, the long pitch, and 7.605 mm (0.2994 inch) for negative and intermediate film, the short pitch.[2] A pitch of 0.300 inch means that 12 inches of film hold 40 frames, so there are 40 frames per foot, which is the figure the calculator uses. At 24 frames per second, that is a speed of 36 feet per minute. A 400 foot roll has 16,000 frames and runs for 11 minutes and 6.7 seconds at 24 frames per second, and a 100 foot roll runs for 2 minutes and 46.7 seconds.
Super 8
The article on Super 8 film describes a cartridge of 50 feet (15 m) of film with 72 frames per foot, for a nominal total of 3,600 frames.[3] It gives 24 frames per second as the professional standard, 18 frames per second as the amateur speed, and says that sound film is typically shot at 18 or 24 frames per second. The running time of a cartridge is 2.5 minutes at 24 frames per second and 3.33 minutes at 18.[3] The calculator agrees: 3,600 frames at 24 frames per second is 2:30, and at 18 it is 3:20. The page also mentions a 200 foot cartridge for magnetic sound, introduced in 1974, which at 18 frames per second runs for 13 minutes and 20 seconds by our calculation.[3]
Standard 8 and Double 8
The article on 8 mm film says that 1 metre of the film contains 264 pictures, each 4.8 by 3.5 mm, and that the usual speeds are 16 or 18 frames per second.[4] The calculator turns the 264 frames per metre into frames per foot by multiplying by 0.3048, which gives 80.4672 frames per foot, and lets you enter the length in either unit. This is our own conversion, as the page gives only the figure per metre. At 16 frames per second a 25 foot spool of 8 mm film, which has 2,012 frames, runs for about 2 minutes and 6 seconds.
Choosing the frame rate
If you leave the frame rate empty, the calculator uses 24 frames per second for 35 mm and 16 mm, 18 for Super 8 and 16 for standard 8 mm. These are the common values, and you can enter any other rate. A higher rate uses more film for each second of the picture and gives smoother motion, a lower rate saves film, and slow motion is made by filming at a faster rate and projecting at the normal one. In that case, calculate the footage with the shooting rate and the running time with the projection rate.
Planning a shoot
To plan, start with the running time you want in the final film, and multiply it by a shooting ratio, the amount of film that you expect to shoot for each unit that is used. Enter the total time, and the calculator gives the film to buy. Compare it with the roll or cartridge sizes on the market, and remember that you may need a little extra for leader and for processing. The film speed result also tells you how fast a camera uses film, which matters when you load it.
Common mistakes
- Using the wrong gauge. The frames per foot differ a great deal between gauges.
- Mixing feet and metres. Choose the unit first.
- Ignoring leader. The usable film is a little shorter than the roll.
- Forgetting slow motion. The shooting and projection rates are different.
What next
Use this often? Add Film to your Home screen.
Frequently asked questions
What is a film calculator?
A tool that converts between the length of motion-picture film, the number of frames and the running time, for several film gauges.
How many frames are in a foot of 35 mm film?
16 frames per foot, so 1,000 feet has 16,000 frames and runs about 11 minutes at 24 frames per second.
How long does a Super 8 cartridge run?
A 50 foot cartridge has 3,600 frames, which is 2.5 minutes at 24 frames per second and 3.33 minutes at 18.
How many frames are in a foot of 16 mm film?
40 frames per foot, from the 0.300 inch frame pitch.
How do I find the film I need for a running time?
Multiply the time in seconds by the frame rate, and divide by the frames per foot.
Sources
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.