An Encounter 5e calculator tells a Dungeon Master how hard a fight will be for a party. Enter the level of each character and the XP value of each monster, and it applies the 2014 encounter-building rules: it adds up the party thresholds, adjusts the monster XP with the right multiplier, and names the difficulty.
How to use the Encounter 5e calculator
- List the levels of the characters, such as 4, 4, 3, 3.
- List the XP of the monsters, using x for a number of the same, such as 450, 50x4.
- Press Calculate.
- Read the difficulty and how much more XP it needs to reach the next step.
The method
The 2014 Basic Rules build an encounter in steps [1]. You find the XP thresholds for each character, add them up for the party, total the monsters' XP, multiply it by a factor for the number of monsters, and compare the result with the party's thresholds [1]. This tool follows those steps and states the version, the 2014 Basic Rules, so that you know which edition the numbers come from.
Thresholds
Each character level has four thresholds, Easy, Medium, Hard and Deadly. At level 1 they are 25, 50, 75 and 100 XP, and at level 20 they are 2,800, 5,700, 8,500 and 12,700 [1]. The two Basic Rules pages that we opened give the same rows [2]. The party's threshold is the sum over all characters.
The multiplier
The XP of the monsters is multiplied according to how many there are: one monster is times 1, two times 1.5, three to six times 2, seven to ten times 2.5, eleven to fourteen times 3, and fifteen or more times 4 [1]. The multiplied figure is the adjusted XP. It is used only to judge the difficulty, and is not the XP that the party earns [1]. Many weak monsters are harder than their raw XP suggests.
Party size
The Basic Rules assume a party of three to five characters. With fewer than three characters, use the next higher multiplier, and with six or more, use the next lower one [1]. The compendium page adds that a single monster against a party of six or more counts as times 0.5 [2]. Where the higher step does not exist, above times 4, the tool keeps times 4 and says so.
Worked example one
A party of two level 4 and two level 3 characters has thresholds of 400, 800, 1,200 and 1,800 XP. One monster of 450 XP and four monsters of 50 XP each total 650 XP, our own example values. With five monsters the multiplier is 2, so the adjusted XP is 1,300. That is above Hard at 1,200 and below Deadly at 1,800, so the encounter is Hard [1]. The thresholds come from the table: a level 4 character has 125, 250, 375 and 500, and a level 3 character has 75, 150, 225 and 400 [2].
Worked example two
Three level 3 characters and one level 2 character have thresholds of 275, 550, 825 and 1,400. One monster of 200 XP and three monsters of 100 XP each, our own example values, total 500 XP. Four monsters give times 2, so the adjusted XP is 1,000, which is Hard [1]. The level 2 character adds 50, 100, 150 and 200 XP to the thresholds [2].
Reading the difficulty
The tool names the highest threshold that the adjusted XP reaches. Below Easy, it says so, because the Basic Rules give no name for it. At or above the Deadly threshold, it says Deadly. It also shows how much more adjusted XP would be needed to reach the next step, which helps you to add or take away a monster. Deadly means that one or more characters could die, so think about the table you play with.
Entering the monsters
The tool does not look up monsters. The challenge rating to XP table is not on the pages that we used, so you enter the XP of each monster from your book or the Monster Manual. Use a comma between values, and x for several of the same: 50x4 is four monsters of 50 XP each. A space also works. The party is entered the same way, so 4x2, 3x2 is two level 4 and two level 3 characters.
Weak monsters
The Basic Rules say to leave out monsters whose challenge rating is significantly below the group's average when you apply the multiplier, unless you judge that they add meaningfully to the difficulty [1]. The tool does not do this by itself, because the judgement is yours. If you add a swarm of minor creatures, the multiplier rises and the encounter looks harder than it plays. Try the calculation with and without them to see how much the number changes.
Using the calculator
Type the levels of all the characters, then the XP of the monsters, and press the button. Check the thresholds, the multiplier and the adjusted XP, then read the difficulty. If you want a harder or easier fight, change the monsters and run it again. This is a guide for planning, and the best test of an encounter is still how your group plays it. The tool covers the 2014 rules only and has no daily XP budget.
Adjusting a fight that is too hard
If the result is harder than you want, the quickest changes are to remove one monster, to swap a strong monster for a weaker one, or to give the party an advantage such as cover or surprise, which the arithmetic does not count. Removing a monster lowers both the raw XP and the multiplier, so the adjusted figure can fall by a large step. Run the calculator again after each change, and remember that tactics, terrain and the party's spells and items can make a fight easier or harder than its rating.
Common mistakes
- Adding the monster XP without the multiplier. The multiplier is part of the method.
- Counting the adjusted XP as a reward. The party earns the raw XP.
- Using the 2024 thresholds. This tool follows the 2014 rules.
- Forgetting a character. Every character adds to the thresholds.
What next
Use this often? Add Encounter 5e to your Home screen.
Frequently asked questions
What is an Encounter 5e calculator?
A tool that rates the difficulty of a Dungeons and Dragons 5e fight from the party's levels and the monsters' XP.
How is encounter difficulty worked out in 5e?
Add the party's XP thresholds, multiply the monsters' XP by a factor for their number, and compare the adjusted XP with the thresholds.
What is the monster multiplier in 5e?
One monster is times 1, two times 1.5, three to six times 2, seven to ten times 2.5, eleven to fourteen times 3 and fifteen or more times 4.
Does the party size change the multiplier?
Yes. With fewer than three characters, use the next higher multiplier, and with six or more, the next lower one.
Does this follow the 2024 rules?
No. It follows the 2014 Basic Rules and is an unofficial fan tool, not affiliated with Wizards of the Coast.
Sources
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.