A Duckworth Lewis calculator works out the revised target for the team batting second when rain or another delay shortens a limited-overs cricket match. Enter the score of the first team and the resources that each team had, and the calculator gives the par score, the target and the score that ties the match. It follows the Standard Edition arithmetic of the Duckworth-Lewis-Stern method, and it works in your browser.
How to use the Duckworth Lewis calculator
- Enter team 1's score.
- If you know both teams' resources, choose I know both resources and enter the two percentages. Otherwise choose which team was interrupted.
- For an interruption, enter the resources left at the interruption, and the resources left at the restart if play resumed. Enter the resources of the other team, which are 100 if it had a full innings.
- Press Work out the target.
What resources are
The method treats an innings as a stock of resources. In the method, each team has two resources with which to score runs, the overs to play and the wickets remaining, and an innings with 50 overs and 10 wickets is 100% of the resources.[1] As overs pass and wickets fall, the resources left go down. The percentages for each combination of overs left and wickets lost come from a published table of resource percentages. This calculator does not include the table, and it asks you to enter the percentages, which you can find in the official regulations of the competition.
The par score
The Standard Edition uses two formulas. When team 2 has the same or fewer resources than team 1, the par score reduces team 1's score in proportion to the reduction in resources, so it is the score of team 1 times the resources of team 2 divided by the resources of team 1.[1] When team 2 has more resources, the par score is the score of team 1 plus G50 times the extra resources divided by 100.[1] G50 is the average score in 50 overs. Wikipedia says that it was changed to 235 for one-day internationals in 2002 and is set each year in the ICC playing handbook.[1] The calculator uses 245 runs as its default, which you can change to the value for your match. The target is the par score rounded up to the next whole number, and the tie score is the par score rounded down.[1]
Resources used in an interrupted innings
If an innings is interrupted and then resumed, the resources used are 100% minus the resources left at the interruption plus the resources left at the restart. If it is cut short and not resumed, the resources used are 100% minus the resources left. These two rules let you use the calculator with the numbers that you read off the table at the moment of the interruption and at the restart.
Worked examples
The examples below are our own working with the formulas above, and the calculator reproduces them. In the first, team 1 scored 231 in 30 overs, and team 2 gets 28 overs. The resources are 75.1% and 71.8%, so the par score is 231 times 71.8 divided by 75.1, which is 220.85, and the target is 221. In the second, team 1 scored 268 and team 2 was cut short with 14.3% of the resources left, so it used 85.7%, the par score is 229.68, the target is 230 and a tie needs 229. In the third, team 1 scored 273 and team 2 was interrupted with 68.6% left and restarted with 46.7%, so the resources used were 78.1%, the par score is 213.21 and the target is 214.
When team 1 is interrupted
In the fourth example, team 1 was interrupted at 44.7% of its resources and restarted at 25.5%, so it used 80.8%. Team 1 scored 170, and team 2 has a full 42 overs with 91.7% of the resources. Team 2 has more resources than team 1, so the par score is 170 plus 245 times 10.9 divided by 100, which is 196.7, and the target is 197. A last example is a match in which 20 overs were lost before the chase, leaving 75.1% for team 2. With team 1 on 240, the par score is 180.24 and the target is 181.
Whole numbers and the tie score
Most par scores are not whole numbers, and then the target is the next whole number and the tie score is the whole number below it. When the par score is exactly a whole number, this calculator gives a target one run higher, so that the target is above the tie score, which matches how the method treats an uninterrupted match.[1]
Limits
The match regulations set the minimum number of overs that must be bowled for a result, so check the rules of your competition. Only the Standard Edition is covered here. Wikipedia says that the Professional Edition has been used in international matches since 2004, and it increases the target in proportion to the extra resources, with no G50 term.[1] The method became the ICC standard in 1999, and before it the average run rate was the most common way to set a target.[1]
Using the calculator in practice
If you follow a match, you can use the calculator to check the target that is announced after a delay. Take the score of the first team, the overs that the second team has, and the resource percentages from the table, and compare the result with the announced target. A difference of a run or two can come from the table of the edition that is used, from the value of G50, or from rounding. For a club match with its own rules, check which version of the method applies.
Common mistakes
- Using overs instead of resources. Enter percentages from the table.
- Forgetting the restart. Leave it blank only if play did not resume.
- Using the wrong G50. 245 is the default for top matches.
- Treating the result as official. The match officials set the target.
What next
Use this often? Add Duckworth Le to your Home screen.
Frequently asked questions
What is a Duckworth Lewis calculator?
A tool that works out the revised target of the team batting second in a rain-affected limited-overs cricket match, from the resources that each team had.
What is the formula?
If team 2 has the same or fewer resources, par = score × R2 ÷ R1. If it has more, par = score + G50 × (R2 − R1) ÷ 100. The target is the par score rounded up.
Where do the resource percentages come from?
From the published Duckworth-Lewis-Stern table of resource percentages, which this tool does not include. You enter them from the official regulations.
What is G50?
The average score in 50 overs. Wikipedia says it was changed to 235 for one-day internationals in 2002 and is set yearly. This tool defaults to 245 runs and you can change it.
Does the tool give the official target?
No. It does the Standard Edition arithmetic. Official targets are set by the match officials.
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.