A cycloid calculator gives the numbers of the curve traced by a point on the rim of a circle that rolls along a straight line: the width, height, length and area of one arch, and for any angle the coordinates of the point, the arc length so far and the slope. Enter the radius of the rolling circle, and an angle if you like, and press the button. The formulas follow the Wikipedia page on the cycloid, and the work is done in your browser.
How to use the cycloid calculator
- Enter the radius r of the rolling circle.
- Choose degrees or radians, and enter the angle t if you want a point on the curve.
- Press Calculate.
The equations of the cycloid
The page gives the cycloid in parametric form, where t is the angle that the rolling circle has turned: x equals r(t − sin t) and y equals r(1 − cos t). One arch of the curve corresponds to t from 0 to 2π, or 0° to 360°. At t = 0 the point is on the line, at the origin. At t = 180° it is at the top of the arch, at x = πr and y = 2r. At t = 360° it has come back to the line, at x = 2πr, and the circle has made one full turn. For r = 2 and t = 180°, the point is at x = 6.28319 and y = 4.
The size of one arch
One arch is 2πr wide, since the circle rolls a distance equal to its circumference, and 2r high, which is the diameter. The page states two results about its length and area. The length of one arch is exactly 8r, which is four times the diameter, and the area under one arch is 3πr², which is three times the area of the rolling circle. For r = 1, that is a length of 8 and an area of 3π, about 9.42478. These results are well known as the first surprises of the calculus of curves, since a curve with no straight parts has a length given by such a simple number.
The arc length along the curve
The speed of the point along the curve is the square root of (dx/dt)² + (dy/dt)², which works out to 2r sin(t/2) for t between 0 and 2π. Adding this up from 0 to t gives the arc length s = 4r(1 − cos(t/2)). At t = 360° this is 8r, which agrees with the length of the whole arch. At t = 180° it is 4r, which is half the length. The calculator gives the arc length at the angle you enter.
The slope of the curve
The slope of the curve at a point is dy/dt divided by dx/dt, which is sin t divided by 1 minus cos t, or cot(t/2). At t = 90° the slope is 1. At the top of the arch, t = 180°, the slope is 0, as expected for the highest point. At t = 0 and t = 360° the curve has a sharp point, a cusp, where the slope is not defined, and the calculator says so.
Scaling the curve
All the numbers of a cycloid scale with the radius. Doubling r doubles the width, the height and the length of an arch, and multiplies the area by four. This is why a single radius is enough to describe the whole curve, and why the calculator can give every number from it. You can use the results to scale a drawing or to check a computation of the path of a point on a rolling wheel.
A worked example with a wheel
Take a wheel with a radius of 5 cm. One arch of the curve traced by a point on its rim is 31.4159 cm wide, 10 cm high and 40 cm long, and the area under the arch is 235.619 cm², while the wheel itself has an area of 78.5398 cm². At a quarter turn, t = 90°, the point is at x = 5(π/2 − 1), which is 2.85398 cm, and y = 5 cm. The distance traveled along the curve so far is 20(1 − cos 45°), which is 5.8579 cm, and the slope is 1. Enter 5 and 90 to confirm these figures.
Relation to the circle
The width of one arch equals the circumference of the rolling circle, since the circle rolls without slipping, and the center of the circle moves in a straight line at height r. The tracing point is at the bottom of its path at t = 0 and the top at t = 180°. Comparing the arch area with the circle shows that the area under the arch is exactly three times the area of the circle, whatever the radius. This is the result that is stated on the page and that the calculator reports.
Common mistakes
- Using the diameter as the radius. The formulas use the radius r.
- Mixing up degrees and radians. Check the unit setting.
- Expecting a circle's area for the arch. The area under one arch is three times as large.
- Taking t as the distance rolled. It is the angle turned, and the distance is rt.
- Giving a slope at a cusp. There is none.
What next
Use this often? Add Cycloid to your Home screen.
Frequently asked questions
What is a cycloid calculator?
A tool for the curve traced by a point on a rolling circle: it gives the size of an arch and the point, arc length and slope at any angle.
What are the equations of a cycloid?
x = r(t − sin t) and y = r(1 − cos t), where t is the angle the circle has turned.
What is the length of one arch of a cycloid?
8r, four times the diameter of the rolling circle.
What is the area under one arch?
3πr², three times the area of the rolling circle.
Where does the cycloid have a cusp?
Where the point touches the line, at t = 0, 360° and so on. The slope is not defined there.
Sources
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.