A Babylonian numerals converter writes a number in the base-60 cuneiform system of ancient Babylon, and reads Babylonian numerals back into an ordinary number. Enter a whole number and press the button, or type the signs π and πΉ grouped by place. The system follows the Wikipedia page on Babylonian cuneiform numerals, and the work is done in your browser.
How to use the Babylonian numerals converter
- Choose the direction: decimal to Babylonian, or Babylonian to decimal.
- Enter the whole number, or the signs or digits for each place.
- Press Convert.
A base-60 system
The page explains that the Babylonians counted in base 60, the sexagesimal system, which is positional, like our base-10 system. Each place is worth 60 times the one to its right. Within a place, the digit is a number from 1 to 59, and only two signs are used to write it: the sign πΉ for one and the sign π for ten. The numbers from 1 to 59 are made by repeating these signs and adding them up, in the way of Roman numerals. For example, 23 is two tens and three ones, which is πππΉπΉπΉ.
Reading and writing a number
To write a number, divide it by 60 repeatedly and write each remainder as a group. For 8,583, the divisions give 8,583 = 2 Γ 3,600 + 23 Γ 60 + 3, so the digits are 2, 23 and 3, and the numeral is πΉπΉ πππΉπΉπΉ πΉπΉπΉ, which is the page's own example. The groups are written next to each other with a space between them. To read a numeral, find the value of each group, and multiply by the power of 60 for its place: 2 Γ 60Β² + 23 Γ 60 + 3 is 7,200 + 1,380 + 3, which is 8,583. The calculator shows these place values.
Empty places
In the system there is no digit for zero. The page says that an empty place was marked with a space, and that a sign for an empty place was used only later and only in the middle of a number, not at the end. This converter marks an empty place with a dot Β·, so 60 is written πΉ Β· and 3,600 is written πΉ Β· Β·. It reads a dot as a zero place too. The page adds that zero is not a number in the system, so the converter does not accept 0.
The missing point
A notable feature of the system is that no radix point was written to separate whole numbers from fractions. The page says that the same signs for 23 could mean 23, 23 Γ 60, 23 Γ 60Β², or 23/60, depending on the context. The calculator reads the last group as the ones, so that πππΉπΉπΉ is 23, and it also shows the number divided by 60 and by 60Β², which are the other readings that are possible. This is the same issue that is faced by readers of cuneiform tablets, who use the problem to decide what size a number must have.
Why base 60 is still with us
The legacy of the system is the 60 minutes in an hour and the 60 seconds in a minute, as well as the 360 degrees of a circle, which are six sixties. The page on the sexagesimal system notes that 60 has many divisors, which makes fractions such as a half, a third, a quarter and a fifth easy to write. The decimal degrees to DMS converter on this site uses the same arithmetic.
More examples
The number 59 is the largest single digit, and it is written with five tens and nine ones: ππππππΉπΉπΉπΉπΉπΉπΉπΉπΉ. The number 60 needs a second group, because each place holds at most 59. It is a one in the 60s place and an empty ones place, written πΉ Β·. The number 3,661, which is one hour, one minute and one second, is 1 Γ 3,600 + 1 Γ 60 + 1, with the digits 1, 1 and 1, and is written πΉ πΉ πΉ, a sign repeated three times. The number of seconds in a day, 86,400, is 24 Γ 3,600, with the digits 24, 0 and 0, and is written with the signs for 24 followed by two empty places.
Working by hand
To convert a number by hand, divide it by 60 and write the remainder. Divide the quotient by 60 again and write that remainder to the left. Repeat until the quotient is 0. For 8,583, divide by 60 to get 143 remainder 3. Then 143 divided by 60 is 2 remainder 23. Then 2 divided by 60 is 0 remainder 2. The remainders, read from the last to the first, are 2, 23 and 3, which are the three groups. Each remainder is then written as tens and ones: the tens digit gives the number of π signs and the units digit the number of πΉ signs.
Typing the signs
The signs are characters of the Unicode block called Cuneiform. If your device does not show them, install or choose a font that supports cuneiform, or copy the result into a document set in such a font. You can type the signs by copying them from the result, or type the base-60 digits as ordinary numbers separated by commas, such as 2, 23, 3, and the converter does the rest. A dot stands for an empty place, so 1, 0 and πΉ Β· both read as 60.
Limits of the converter
The converter handles whole numbers from 1 up to one trillion, which needs up to 7 places, and reads numerals of up to 8 places. The ancient tablets also wrote fractions, and the tool shows the number divided by 60 and by 3,600 as an aid, but it does not choose between the possible readings, since the ancient system did not either.
Common mistakes
- Writing a place with more than 59. Each place holds a digit from 0 to 59.
- Reading the groups from the wrong end. The leftmost group is the highest place.
- Forgetting the empty place. 60 needs a second group.
- Expecting a sign for zero. The ancient system had none for the number zero.
- Taking the size for granted. The same signs can stand for several sizes.
What next
Use this often? Add Babylonian N to your Home screen.
Frequently asked questions
What is a Babylonian numerals converter?
A tool that writes a number in the base-60 cuneiform numerals of ancient Babylon and converts such numerals back to decimal.
How do Babylonian numerals work?
They are base 60 and positional. Each place holds 1 to 59, written with π for ten and πΉ for one.
What is 8,583 in Babylonian numerals?
πΉπΉ πππΉπΉπΉ πΉπΉπΉ, which is 2 Γ 60Β² + 23 Γ 60 + 3.
Did the Babylonians have a zero?
Not as a number. An empty place was left as a space, and a placeholder sign came later, only inside numbers.
How did they write fractions?
They did not mark a point, so the same signs could stand for 23, 23 Γ 60 or 23/60, depending on the context.
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.