An angle of impact calculator finds the angle at which a drop of liquid hit a surface from the width and the length of the stain it left. A round stain means a drop that landed square on, and a long thin stain means a shallow angle. Optionally it also estimates how high the drop started.
How to use the angle of impact calculator
- Choose US or metric units.
- Enter the width and the length of the stain, without the tail.
- Add the distance to the origin if you want a height.
- Press Calculate.
The idea behind it
When a drop of liquid hits a surface at an angle, it spreads into an ellipse. The shape of the ellipse tells you the angle: the shallower the angle, the longer and narrower the stain. The Wikipedia page on bloodstain pattern analysis says that investigators measure the length and width of the droplet and use the formula sin(A) = width ÷ length [1]. We follow that rule, and we explain below which parts we added ourselves.
The formula
The angle of impact is the inverse sine, or arcsine, of the width divided by the length. Wikipedia gives the relationship as a sine [1], and finding the angle by taking the arcsine is our own step, which follows directly from it. The width must be no bigger than the length, since a sine cannot exceed 1. A stain with a width equal to its length is round, and gives 90 degrees. A stain that is half as wide as it is long gives 30 degrees.
Measuring the stain
Measure the width across the narrow part of the ellipse, which is the minor axis. Measure the length along the long part, the major axis, and leave out the tail, because the tail is not part of the ellipse. Wikipedia notes that a stain may have a tail that shows the direction of travel [1]. Use a ruler with fine marks or a magnifier, and take both measurements in the same unit. Small errors in the width matter most when the stain is nearly round.
Worked examples
These worked cases are our own arithmetic with the formula, and you can try them in the calculator. A stain 2.1 wide and 2.3 long gives 65.93 degrees. A stain 1.4 wide and 1.7 long gives 55.44 degrees. A stain 1.9 wide and 3.1 long gives 37.80 degrees. A stain of length 2 and width 1 gives 30 degrees. Try them in the metric mode, where the units do not matter to the angle, because it is a ratio. The angle is the same whether you measure in centimetres or inches.
Estimating the height
To find the height of the origin, we multiply the distance from the stain to the point of origin on the surface by the tangent of the angle. This comes from the right triangle of the drop path and the surface, and it is our own working. With a stain at 65.93 degrees and a distance of 33 centimetres, the height is 33 times tan 65.93, which is about 73.9 centimetres. Wikipedia mentions a related tangent method for finding the source of fast-moving drops with flat paths [1], but it gives no formula for it, so we cite it only for the idea.
A straight line assumption
The method assumes a straight line from the origin to the stain. Gravity, air resistance and viscosity are ignored, and a real drop follows a curved path. Wikipedia says that the tangent method works best for fast-moving drops with flat trajectories, and that the curvature may lead to errors [1]. We cannot say how large the error is, but it can be large for slow drops. For this reason the height from the tool is a rough estimate that is best used to compare cases, and not a precise measurement.
Surface and tail effects
The Wikipedia page notes that rough or porous surfaces, including fabrics, can disrupt the surface tension of a drop and give distorted stains with spines or satellite stains [1]. As our own comment, a smooth surface is likely to give a cleaner ellipse. Choose stains that have clear edges for the measurement, and measure several, then compare. The calculator cannot correct for surface effects. It assumes that the stain you measured is a clean ellipse.
Using US or metric units
The angle needs no unit. The units matter only for the optional distance and for the height that comes from it. In US mode, you enter inches and read the height in inches. In metric mode, you enter centimetres and read centimetres. Use the same unit for the width and the length.
Good uses
A safe way to practise the method, and this suggestion is our own, is to drop coloured liquid onto card from a known height at a known angle, measure the stain, and compare the answer with the true angle.
Limits
The calculator gives an approximate angle of a single drop under a straight-line model. It does not account for gravity, air resistance or viscosity. It is not a forensic tool, and it should never be used as evidence or to reach a conclusion about a real event. A result for a stain where the width is larger than the length is an error, so the tool asks you to check the measurements instead of giving a value.
Common mistakes
- Including the tail in the length. Measure the ellipse only.
- Swapping the width and the length. The width is the shorter side.
- Mixing inches and centimetres. Use one unit for all three numbers.
- Treating the height as exact. It is a rough straight-line estimate.
What next
Use this often? Add Angle of Imp to your Home screen.
Frequently asked questions
What is an angle of impact calculator?
It is a tool that finds the angle at which a drop hit a surface from the width and the length of the stain it left.
What is the angle of impact formula?
The angle equals the arcsine of the stain width divided by its length. A stain 1 wide and 2 long gives 30 degrees.
How do I find the height of the origin?
Multiply the distance from the stain to the point of origin on the surface by the tangent of the angle. A stain at 65.93 degrees and 33 centimetres gives about 73.9 centimetres.
Should the tail be included in the length?
No. Measure only the elliptical body of the stain and leave the tail out.
How accurate is the result?
It assumes a straight-line path and ignores gravity and air resistance, so the height can be well off. Use it for study, not as evidence.
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.