A Taylor rule calculator estimates the interest rate that a central bank following the Taylor rule would set. Enter the inflation rate, the inflation target, the natural real interest rate and the output gap. The calculator gives the suggested nominal policy rate, along with the real rate it implies and how much each gap contributes.
The Taylor rule formula
i = π + r* + aπ × (π − π*) + ay × output gap
output gap = 100 × (Y − Ȳ) ÷ Ȳ
Wikipedia's Taylor rule article gives the target nominal rate i as the inflation rate π plus the assumed natural real rate r*, plus a weight aπ times the gap between inflation and its target π*, plus a weight ay times the output gap. The output gap is actual GDP less potential output, as a percentage of potential. The article says the weights should be positive, and that Taylor's 1993 paper proposed setting both to 0.5. The rule was proposed in 1992 by John B. Taylor.
How to use the Taylor rule calculator
- Enter the current inflation rate and the target.
- Enter the natural real rate you assume.
- Enter the output gap as a percentage of potential output.
- Optionally change the weights, then press Calculate.
Worked example
Suppose inflation is 3 percent against a target of 2 percent, the natural real rate is 2 percent and output is 1 percent above potential. With weights of 0.5 each, the rule gives 3 + 2 + 0.5 × (3 − 2) + 0.5 × 1 = 6.0 percent. The real rate, 6 minus 3 inflation, is 3 percent, which is above the assumed natural rate of 2 and so represents tighter policy. The inputs are assumed for the illustration: the article itself gives no worked example.
How to read the result
The article explains that the rule calls for a higher real interest rate, tight policy, when inflation is above target or output is above potential, and a lower real rate, easy policy, in the opposite case. The rule is therefore counter-cyclical. The calculator shows each gap's contribution so that you can see which one is pushing the suggested rate up or down. A negative inflation gap and a negative output gap both lower the rate.
The Taylor principle
The article describes the Taylor principle: because the weight on inflation is positive, a rise in inflation of one percentage point should lead to a rise in the nominal rate of more than one point, namely 1 plus the weight. With a weight of 0.5, that is 1.5 points. The calculator shows this figure. The idea is that the real interest rate must rise when inflation rises, otherwise policy would become looser just as inflation was climbing.
The natural rate and the output gap
The rule needs two numbers that cannot be observed directly. The natural real rate is the assumed equilibrium rate, and the output gap compares actual GDP with a potential output that is itself an estimate. The article notes that the rule's results depend on these estimates, and discusses limitations of the rule. Use values from a source you trust, and try a range to see how much the answer moves. The GDP gap calculator works out an output gap from actual and potential GDP.
Changing the weights
The default weights of 0.5 follow Taylor's 1993 proposal, but the article says only that they should be positive. A higher weight on inflation makes the suggested rate respond more strongly to inflation, and a higher weight on the output gap makes it respond more to the state of the economy. Setting the output weight to zero gives a rule that responds only to inflation. Try different weights to see how sensitive the result is to the choice.
Related tools
The real rate in the result follows the relationship covered by the Fisher equation calculator. To measure inflation from price indexes, the GDP deflator calculator is one way, and the percentage calculator works out any percentage change.
A second example with slack
Suppose inflation is 1 percent against a target of 2 percent, the natural real rate is 2 percent and output is 3 percent below potential. With weights of 0.5, the rule gives 1 + 2 + 0.5 × (1 − 2) + 0.5 × (−3) = 1 percent. Both gaps pull the rate down, from the 3 percent that inflation plus the natural rate would give. The real rate is zero, well below the assumed natural rate of 2 percent, which is easy policy, as the article describes for a weak economy.
When the rule gives a negative rate
If inflation is low and the economy is far below potential, the formula can produce a negative number. The calculator reports the figure and flags it, because the rule itself places no floor on the rate. Whether a central bank can set a negative rate is a separate question from what the rule suggests. Treat a negative result as a sign of how much easing the rule would call for, not as a rate any bank must set.
Using the rule to compare
The rule is most useful as a benchmark. Compare the rate it suggests with the actual policy rate to see whether policy looks tighter or looser than the rule would imply. Differences can arise for good reasons, such as uncertainty about the natural rate or other goals, so a gap is a prompt for questions rather than proof that policy is wrong. Recalculating with different estimates of the natural rate and the output gap shows how robust the comparison is.
Common mistakes
- Using the wrong inflation measure. The article specifies the GDP deflator.
- Entering the gap as a decimal. Enter 1 for 1 percent.
- Treating the rule as a prediction. It is a guide, not what a bank will do.
- Forgetting the natural rate is an estimate. Test a range.
What next
Use this often? Add Taylor Rule to your Home screen.
Frequently asked questions
How does a Taylor rule calculator work?
It adds inflation and the natural real rate to weighted gaps between inflation and target and between output and potential.
What weights did Taylor propose?
0.5 on both gaps, in his 1993 paper, according to Wikipedia.
What is the Taylor principle?
A one-point rise in inflation should raise the nominal rate by more than one point.
What is the output gap?
Actual GDP less potential output, as a percentage of potential.
Does the rule predict what central banks will do?
No. It is a rule of thumb, and results depend on estimates of the natural rate and output gap.
Sources
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.