Saved

Press the star next to a tool's name to save it.

All my tools

Speaker Test

Choose a channel and a sound, and this speaker test plays a tone through your left, right or both speakers, so you can check that they work and are wired correctly.

Restored your last values ·

Tones last 5 seconds and the sweep lasts 10 seconds. Changing a setting while it's playing restarts the sound.

The sounds are made on your device. Nothing is recorded or uploaded.

Status

–

Turn your volume down before you start, especially with headphones. Stop if a sound is uncomfortable.

Recent results

A speaker test tells you quickly whether your speakers or headphones are working, and whether the left and right sides are connected the right way round. Choose a speaker, pick a sound, and press play. This speaker test generates clean tones right on your device, including low, middle and high frequencies and a sweep across the whole range of normal hearing. There is nothing to install or download, and it works with computer speakers, laptop speakers, headphones and earbuds. Remember to turn your volume down before you start.

How to use the speaker test

  1. Turn your device's volume down to a low level.
  2. Choose Left, Both or Right.
  3. Pick a sound: a low, middle or high tone, or a sweep.
  4. Press Play test sound, and slowly raise the volume if you need to.
  5. Listen carefully, and then try the other side.

What are the left and right channels?

Stereophonic sound, usually shortened to stereo, recreates a sense of direction by using two independent audio channels, played through two loudspeakers or a pair of headphones. If the channels are swapped, sounds appear to come from the wrong side. In music you might not notice, but in films and games it can be distracting. To check, choose Left. The sound should come only from your left speaker or the left earpiece. Then choose Right and listen again.

The sounds in this test

  • Low (100 Hz): a deep hum for checking bass response. Very small speakers may produce only a little of it.
  • Mid (440 Hz): a clear, steady tone in the range where hearing is comfortable, and a good first test.
  • High (8,000 Hz): a sharp, thin tone for checking tweeters and the treble in headphones.
  • Sweep: a tone that rises smoothly from 20 Hz to 20,000 Hz over ten seconds.

What can you hear?

The range of human hearing is commonly given as 20 to 20,000 Hz, although there is considerable variation between people, especially at high frequencies, and a gradual loss of sensitivity to higher frequencies with age is considered normal. So if you can't hear the very top of the sweep, your speakers aren't necessarily at fault. Also, this isn't a hearing test. If you are concerned about your hearing, speak to a qualified professional, who can carry out a proper assessment.

Troubleshooting: no sound

  • Check the volume and mute settings on your device, and in the browser tab as well.
  • Check the output device. Your computer may be sending sound to a monitor or a Bluetooth device.
  • Check the cables and make sure that powered speakers are switched on.
  • Reconnect Bluetooth headphones, and check that they are charged.
  • Try another app. If nothing plays anywhere, the problem isn't with this page.

Troubleshooting: one side is silent

If only one side works, first check that your device's balance control is centered. Then swap the two speakers or turn your headphones around. If the fault stays on the same side, it's probably in the source, the socket or the cable. If it moves with the speaker, the speaker or earpiece itself is likely to be at fault. With wired headphones, gently bending the cable near the plug during a tone can reveal a broken wire, if the sound crackles or cuts in and out.

Listening for rattles and distortion

A sweep is good for finding problems. As the pitch rises, a loose part can buzz or rattle at a particular frequency. A speaker in poor condition may sound rough or distorted, rather than producing a pure tone. Listen for sudden changes in volume, or points where the sound nearly disappears, although room reflections and the shape of the speaker cabinet can have those effects too. Moving your position slightly will help you to tell the difference.

Protecting your hearing and your speakers

Pure tones can seem much louder and harsher than music, so begin with your volume low and raise it gradually. Keep particular care with headphones and earbuds, as they deliver sound straight into your ears. High volumes can also damage small speakers, especially at very low frequencies. Take a break if the tones are unpleasant, and stop at once if you feel any discomfort.

Is anything recorded?

No. The sounds are generated by your browser, and this page doesn't use your microphone. Nothing is recorded, uploaded or saved.

When to test your speakers

A quick check is useful whenever you set up a new computer, connect a new pair of speakers, or change your room layout. It's also worth running before an important online meeting, a presentation or a gaming session, so that you aren't caught out at the last moment. When you buy used speakers or headphones, test each side and listen to the sweep before you pay, if the seller lets you.

Common mistakes

  • Testing at full volume. Start low and go up gradually.
  • Forgetting Bluetooth is connected. The sound may be playing somewhere else.
  • Blaming speakers for the top of the sweep. Many adults can't hear it.

Check your recording setup with the microphone test, make sure your camera works with the webcam test, and see how fast you can type with the typing speed test.

What next

Use this often? Add Speaker Test to your Home screen.

Frequently asked questions

How does the speaker test work?

Your browser generates a pure tone and sends it to the left, right or both channels of your audio output.

Why can't I hear the end of the sweep?

Many people can't hear the highest frequencies, and small speakers may not reproduce them.

Why is there no sound?

Check your volume, mute settings, output device and connections, then try again.

Can I test headphones?

Yes. Turn the volume down first, then test the left and right sides separately.

Is my microphone used?

No. This test only plays sound, and nothing is recorded.

What went wrong?

We only receive the reason you pick, never what you typed into the tool.

Thanks for your feedback.

More Developer Tools