This relative fat mass calculator estimates your body fat percentage from just your height and waist measurement. Choose your sex, enter your height and waist, and the relative fat mass calculator works out your RFM, an estimate of whole-body fat percentage, and shows how it compares with the cut-points used in the study that introduced it.
How to use the relative fat mass calculator
- Choose US (inches) or metric (cm). US is the default.
- Choose your sex.
- Enter your height and your waist in the same unit.
- Press Calculate to see your estimated body fat percentage.
What is relative fat mass?
Relative fat mass (RFM) is a simple formula for estimating body fat from the ratio of height to waist. It was published in 2018 in Scientific Reports by Orison Woolcott and Richard Bergman, who set out to find a simple equation that estimates whole-body fat percentage more accurately than body mass index (BMI). The authors describe it as a simple equation that is more accurate than BMI for estimating whole-body fat percentage.
The RFM formula
The study's equation is:
RFM = 64 − (20 × height ÷ waist) + (12 × sex)
where sex = 0 for men and 1 for women
So for men it's 64 − 20 × height ÷ waist, and for women 76 − 20 × height ÷ waist. Because the formula uses a ratio, height and waist just need to be in the same unit: inches, centimeters or meters all give the same answer.
How RFM was developed
Woolcott and Bergman used data from the US National Health and Nutrition Examination Survey (NHANES) for adults 20 and older. They built the equation from 12,581 people in the 1999–2004 surveys, testing 365 different body measurement indices, and then checked it on 3,456 people from the 2005–2006 survey. In that validation group, RFM predicted body fat measured by dual-energy X-ray absorptiometry (DXA) better than BMI did, for both women and men.
Worked example
Take a man who is 70 inches tall with a 36-inch waist. His height-to-waist ratio is 70 ÷ 36 = 1.94, so RFM = 64 − 20 × 1.94 = 25.1%.
Now take a woman who is 65 inches tall with a 32-inch waist. Her ratio is 2.03, so RFM = 76 − 20 × 2.03 = 35.4%. In metric, a woman who is 165 cm tall with an 80 cm waist has an RFM of 76 − 20 × 2.06 = 34.8%.
Reading the results
The big number is your estimated body fat percentage. The line below compares it with the cut-points the study used: 33.9% body fat for women and 22.8% for men. The table shows your height-to-waist ratio and the cut-point for your sex.
About the cut-points
The study needed a way to compare how often RFM and BMI misclassify obesity, so it defined obesity using arbitrary DXA body fat cut-points of 33.9% or more for women and 22.8% or more for men. Using those same cut-points, RFM picked out 95.0% of women and 96.2% of men with obesity. The authors are clear, though, that their study wasn't designed to propose RFM cut-points for diagnosing obesity, and the study was cross-sectional, so it did not test which values relate to health problems over time. So treat the comparison as a guide, not a diagnosis.
How to measure your waist
In the NHANES surveys, waist was measured with a tape placed around the bare waist, level with the top of the right hip bone, standing, at the end of a normal breath out. Measuring the same way at home gives the closest match to the formula. Keep the tape level and snug, without pressing into the skin.
Limits of RFM
The study notes that RFM was developed and checked on US adults of Mexican, European and African ancestry, and that it still needs testing in other populations, in children, in athletes and in people with specific diseases. It's an estimate for an average adult with your measurements, so a DXA scan or another direct test will be more accurate for you.
Why not just use BMI?
BMI uses only height and weight, so it can't tell fat from muscle. The RFM study notes earlier research finding that a BMI of 30 or more would miss nearly half of women whose body fat was above 35%. RFM uses the waist, where much body fat is stored, which is one reason it tracked DXA body fat more closely in the study.
How your waist changes the result
Because the waist is in the bottom of the ratio, a bigger waist gives a higher RFM. For the 70-inch man in the example, each extra inch of waist adds about one percentage point: a 37-inch waist gives 26.2% and a 35-inch waist gives 24.0%. That makes RFM easy to track as your waist changes.
Common mistakes
- Measuring at the belly button. Use the top of the hip bone.
- Mixing units. Enter height and waist in the same unit.
- Using it for children. It was built for adults 20 and older.
- Treating the cut-point as a diagnosis. It was chosen for comparison only.
Tips
- Measure your waist two or three times and use the average.
- Track RFM over months rather than days.
- Use it alongside BMI and a body fat test for a fuller picture.
What next
Use this often? Add Relative Fat to your Home screen.
Frequently asked questions
How does a relative fat mass calculator work?
It uses the RFM formula: 64 − 20 × height ÷ waist, plus 12 for women, with height and waist in the same unit.
What is a normal relative fat mass?
The study didn't set normal ranges. It used 33.9% for women and 22.8% for men as arbitrary obesity cut-points for comparison.
Is RFM more accurate than BMI?
In the 2018 study, RFM predicted DXA-measured body fat better than BMI for both women and men.
Where do I measure my waist for RFM?
Around the bare waist, level with the top of the hip bone, standing, after breathing out.
Who can use the relative fat mass calculator?
It was developed for adults 20 and older and hasn't been tested in children or athletes.
Sources
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.