A parking ratio calculator turns the number of parking spaces and the size of a building into the usual ratio of spaces per 1,000 square feet. It also shows the building area behind each space and, if you enter a target ratio, how many spaces the building needs and whether you have a surplus or a shortfall.
How to use the parking ratio calculator
- Enter the building area and choose US or Metric units.
- Enter the parking spaces provided.
- Optionally enter a target ratio in spaces per 1,000 square feet, then press Calculate.
What a parking ratio is
The parking ratio compares the number of parking spaces with the size of the building they serve. Listings, leases and zoning documents usually state it as spaces per 1,000 square feet of building area. Zoning documents state requirements in this form: the Salt Lake City schedule, for example, lists office uses as spaces per 1,000 square feet of gross floor area [1]. This page works the ratio out as parking ratio = 1,000 × parking spaces ÷ building area, which is our own arithmetic. A higher ratio means more spaces for every square foot of building, which usually makes parking easier. A lower ratio means a tighter lot or garage.
The formula, step by step
Divide the number of spaces by the building area, then multiply by 1,000. The factor of 1,000 only gives a ratio of a convenient size, because the raw ratio would be a small decimal. If you enter the area in square metres, the calculator first converts it with 1 square metre = 10.7639 square feet, which is our own working and not taken from the source. The ratio is always shown per 1,000 square feet, and the same figure per 100 square metres is shown beside it.
A worked example
Take 1,000 parking spaces for a building of 25,000 square feet. The ratio is 1,000 × 1,000 ÷ 25,000 = 40 spaces per 1,000 square feet, and the calculator returns the same value. The example is our own.
Building area per space
Dividing the building area by the number of spaces gives the floor area behind each space. In the example, 25,000 ÷ 1,000 = 25 square feet of building for every space. This figure is our own working. It is a quick check: a ratio of 4 per 1,000 square feet means 250 square feet of building for each space, and a ratio of 2 means 500 square feet.
Spaces needed at a target ratio
If a lease, a lender or a planner gives you a target ratio, enter it in the optional box. The spaces needed are the building area ÷ 1,000 × the target ratio, rounded up to a whole space, which is our own working. For 25,000 square feet and a target of 4, the need is 25 × 4 = 100 spaces, so a lot with 1,000 spaces has a surplus of 900. The tool reports a surplus or a shortfall and the number of spaces.
Where target ratios come from
The tool has no built-in standard, because the right target depends on the use of the building and on local rules. Salt Lake City's schedule, for instance, asks for 3 spaces per 1,000 square feet of gross floor area on the main floor of a general office, plus 1 1/4 spaces per 1,000 square feet for each additional level [1]. That table dates from 2012, so treat it as an example of the format. The Wikipedia article on parking mandates describes the Institute of Transportation Engineers guide as a guidebook of statistical data, and notes that it does not explicitly state what parking minimums should be. It also reports that Washington state law SB 5184 caps minimums at 0.5 spaces per residential dwelling unit and two spaces for every 1,000 square feet of commercial space [2]. Local zoning codes set their own minimums, and they differ by city and by use, so check your own code before you rely on any number.
Rentable and gross area
A parking ratio may be quoted against the rentable area or against the gross building area, and the two give different results for the same building. The Salt Lake City schedule bases its figures on gross floor area [1]. The calculator uses whichever area you enter, so use the same basis as the document you are comparing it with. A lease that offers 4 spaces per 1,000 rentable square feet is not the same as 4 per 1,000 gross square feet, and the difference grows with the amount of corridor, lobby and plant space.
US and metric units
Choose Metric to enter the area in square metres. The result is still given per 1,000 square feet, because that is how the ratio is normally quoted, and also per 100 square metres. For 2,322.576 square metres and 1,000 spaces, the ratio is 40 per 1,000 square feet, which is 43.056 per 100 square metres. The building area per space is shown in both square feet and square metres.
What the ratio does not tell you
The ratio is an average over the whole building. It does not show how many spaces are in use at peak hours, how many are reserved, accessible or for visitors, whether parking is shared with a neighbour, or how many people arrive by bus, by bike or on foot. None of our sources gives a peak-demand figure, so the tool does not model one. Treat the ratio as a measure of supply, not of demand.
Using the result
Use the ratio to compare buildings or to test a site plan against a zoning minimum. If the tool shows a shortfall, the number of missing spaces tells you what you would have to add, or how much building area the existing spaces could support at your target. Always confirm the final figure with the local planning office or your adviser before you sign or build.
Common mistakes
- Mixing rentable and gross area. The same building has two different ratios.
- Entering the target in the wrong unit. The target is spaces per 1,000 square feet, not per 100 square metres.
- Counting spaces you do not control. Only count spaces that the building really has the right to use.
- Treating the ratio as a legal minimum. Zoning rules set the minimum, and they vary.
What next
Use this often? Add Parking Rati to your Home screen.
Frequently asked questions
What is a parking ratio calculator?
A tool that divides the number of parking spaces by the building area and shows the result as spaces per 1,000 square feet.
How do you calculate the parking ratio?
Parking ratio = 1,000 × parking spaces ÷ building area in square feet. For 1,000 spaces and 25,000 square feet it is 40.
What is a good parking ratio?
There is no single figure. It depends on the use of the building and on local zoning rules, so enter your own target ratio.
Does the parking ratio use rentable or gross area?
Either can be used, and they give different results. Use the same basis as the lease or zoning document you are comparing with.
How many spaces do I need for 25,000 square feet at 4 per 1,000?
25,000 ÷ 1,000 × 4 = 100 spaces, rounded up to a whole space.
Sources
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.