Saved

Press the star next to a tool's name to save it.

All my tools

Mobius Strip Calculator

Use this Mobius strip calculator to find the edge length and surface area of a Möbius strip from the length and height of the paper, and the band that a cut down the middle leaves.

Restored your last values ·

Choose US or metric units, enter the length and the height of the paper strip, and choose how many half twists to give it before gluing the ends. You get the number and length of the edges and the surface area. Choose the cut option to see what a cut down the middle leaves.

Everything is worked out in your browser. Nothing you type is sent anywhere.

–

–

Enter the length and the height of the strip, then press Calculate.

See full result

A Mobius strip calculator works out the edge length and the surface area of a Möbius strip made from a paper strip, and shows what is left when you cut it down the middle. Enter the length and the height of the strip, choose the number of half twists, and press Calculate.

How to use the Mobius strip calculator

  1. Choose US or metric units.
  2. Choose Make the strip or Cut it down the middle.
  3. Choose the number of half twists.
  4. Enter the length and the height of the strip and press Calculate.

What a Möbius strip is

A Möbius strip is made by taking a long strip of paper, giving one end a half twist and gluing the two ends together. The result has only one side and one edge. Wikipedia says that Möbius strips can be built with any odd number of half-twists, and that the strip has only a single boundary curve [1]. A single half twist is the usual choice, and it is the default here.

The edge length

A plain ring has two edges, each as long as the strip. A Möbius strip has only one, and Wikipedia says its length is twice the length of the centerline of the strip [1]. So for a strip 30 centimetres long, the single edge is 60 centimetres long. The calculator doubles the length for a strip with one half twist, which is the answer that you get when you run a thread along the edge and find that you have gone round the loop twice.

The surface area

Take a strip 30 centimetres long and 25 centimetres high. The rectangle has an area of 30 × 25 = 750 square centimetres, and the tool reports an area of 1,500 square centimetres, which is twice that. The reason is that the figure counts both faces of the paper, and a Möbius strip has only one surface that runs over both. This two-times rule is our own working, because the page we read gives no area formula.

Cutting it down the middle

Cutting a Möbius strip along the middle does not give two strips. Wikipedia says that you get one long strip with four half twists, which is not a Möbius strip but is topologically a cylinder [1]. Our calculator gives its size, which is our own working: the new band is twice as long as the old strip and half as high. For the 30 by 25 strip, that is 60 by 12.5 centimetres, with two edges of 60 centimetres and two surfaces of 750 square centimetres each.

A worked example in inches

Take a strip 12 inches long and 10 inches high, with one half twist. The single edge is 2 × 12 = 24 inches long, and the one surface has an area of 2 × 12 × 10 = 240 square inches. After a cut down the middle, you get one band of 24 by 5 inches, with two edges of 24 inches and two surfaces of 120 square inches each. The total area is still 240 square inches, as the cut takes away no paper in this model.

None or two half twists

The calculator also accepts no twist and two half twists. Wikipedia says that an even number of twists gives an annulus [1]. The counts here are our own working from simple counting. With no twist, the strip becomes a plain ring with two edges and two surfaces. With two half twists it is a band with a full twist, which also has two edges and two surfaces. A cut down the middle gives two separate rings in the first case, and in the second case two rings that are linked together, which is the standard result.

Units

In US mode, you enter the length and the height in inches, and the results are in inches and square inches. In metric mode, they are in centimetres and square centimetres. If you enter 30 and 25 in metric mode you get the example above. The maths is the same in both modes, and only the labels change. The height of a strip is its width, the distance across the paper from one long edge to the other.

What is left out

The page that we read gives no area formula and no sizes for the cut strips, so the formulas here are our own working. We do not model the overlap at the glued joint, as the page does not say what effect it has. Wikipedia says that cutting the strip one third of the way across gives two linked strips, one a thinner Möbius strip and one with two half twists [1], but it gives no sizes, so the calculator offers only the cut down the middle.

Try it at home

Cut a strip of paper about 30 centimetres long and 3 centimetres wide, give one end a half twist and tape the ends together. Run a pencil along the middle without lifting it: you will return to the start having marked both faces, which shows that there is one side. Then cut along the pencil line and see the result. The calculator tells you in advance how long the new band will be, and how wide.

Common mistakes

  • Using an even number of twists. Only an odd number gives a Möbius strip.
  • Expecting two strips after the cut. You get one longer band.
  • Forgetting that the area counts both faces. It is twice the rectangle.
  • Mixing inches and centimetres. Check the units option.

What next

Use this often? Add Mobius Strip to your Home screen.

Frequently asked questions

What is a Mobius strip calculator?

A tool that finds the edge length and the surface area of a Möbius strip made from a paper strip of a given length and height, and the size of the band left after a cut down the middle.

How long is the edge of a Möbius strip?

Twice the length of the strip, as the single edge goes round the loop twice.

What happens when you cut a Möbius strip down the middle?

You get one band, twice as long and half as wide, with four half twists. It is no longer a Möbius strip.

How many half twists make a Möbius strip?

An odd number. One half twist is the usual choice.

Does the calculator work out a cut at one third of the width?

No. That cut gives two linked strips, and the page we used does not give their sizes.

What went wrong?

We only receive the reason you pick, never what you typed into the tool.

Thanks for your feedback.

More Math Tools