A 5/3/1 lifting calculator turns your one-rep max, or your training max, into the weights for each set of Jim Wendler's 5/3/1 program. Enter one number, choose pounds or kilograms, and you get the warm-up sets and the three weeks of work sets for the squat, bench press, overhead press or deadlift, rounded to the plates you have. It also shows the training max to use for the next cycle. It runs in your browser and nothing you enter is sent anywhere.
What 5/3/1 is
The Fitness Wiki describes 5/3/1 as a family of programs in which you do the squat, deadlift, overhead press and bench press using percentages of a training max. This calculator follows the page on 5/3/1 for Beginners, which is a companion to Jim Wendler's own article. The page says that on each of the three lifting days you do eight sets of two main lifts, with the third set of each one being an AMRAP set, which means as many reps as possible, followed by assistance work.
How to use the 5/3/1 lifting calculator
- Choose US (pounds) or Metric (kilograms).
- Choose whether the number you enter is your estimated one-rep max or your training max.
- Enter the weight.
- Optionally enter the amount to round the bar weight to, such as 5 lb or 2.5 kg.
- Press Build my 5/3/1 week.
The training max
All the weights are percentages of a training max. When you start, the page says to work up to a weight you can lift 3 to 5 times with good bar speed, use that to estimate your one-rep max, and take 90 percent of it as your starting training max. It stresses that this is the only time the training max is so closely tied to your one-rep max. As you go through the program your strength rises above the training max, and that is intended, since the training max is there to set your workouts, not to measure your strength.
The sets and reps
The page gives a three-week cycle. In week 1 you do 5 reps at 65 percent, 5 reps at 75 percent and 5 or more reps at 85 percent. In week 2 you do 3 reps at 70 percent, 3 at 80 percent and 3 or more at 90 percent. In week 3 you do 5 reps at 75 percent, 3 at 85 percent and 1 or more at 95 percent. The plus sign marks the AMRAP set, which should not be to absolute failure, and you stop when the bar speed slows a lot. The optional warm-up is 5 reps at 40 percent, 5 at 50 percent and 3 at 60 percent.
Worked example
The Fitness Wiki gives a squat example with an estimated one-rep max of 215 and a training max of 190. Week 1, day 1 is 125 for 5, 140 for 5 and 160 for 5 or more. You can check this with the calculator: choose training max, enter 190 and a rounding of 5. If you enter a one-rep max of 300 pounds instead, the training max is 270, and week 1 is 175 for 5, 205 for 5 and 230 for 5 or more.
Rounding
The calculator rounds each weight to the nearest step you choose, and a weight exactly halfway between two steps is rounded down, as in the wiki example where 75 percent of 190, which is 142.5, becomes 140. Use 5 pounds if you have 2.5 pound plates on each side, or 2.5 kilograms if you have 1.25 kilogram plates. A smaller step follows the percentages more closely.
Progression
At the end of each cycle you add weight to the training max: 5 pounds for the upper body lifts, which are the bench press and the overhead press, and 10 pounds for the lower body lifts, which are the squat and the deadlift. You add the same amount however many reps you got on the AMRAP sets. The calculator shows both numbers. In kilograms it uses 2.5 for upper body and 5 for lower body, which are my rounded metric equivalents of the page's figures.
Why the progress seems slow
The page answers a common worry: the training max rises more slowly than in programs that add weight every session, but the aim is steady progress over a long time, training below your maximum. Be patient, keep the reps crisp, and avoid grinding reps.
Assistance work
The Fitness Wiki page says that after the main lifts you choose one push exercise, one pull exercise and one single leg or core exercise each day and do 50 to 100 reps of each. Examples include dips and push-ups for pushing, chin-ups and rows for pulling, and lunges or ab work for the single leg and core. It says not to overthink the choice, since the point is to get a lot of full-body volume done.
The three lifting days
The program on that page has three days a week. Day 1 on Monday is the squat and the bench press, day 2 on Wednesday is the deadlift and the overhead press, and day 3 on Friday is the bench press and the squat. The calculator gives the weights for one lift; run it again with the training max of each lift. Keep a note of each training max so that you can add 5 or 10 pounds when the cycle ends.
First set last sets
After the three core sets, the page adds five sets of five at the weight of the first set of the day. For week 1 this is five sets of 5 at 65 percent, for week 2 it is five sets of 5 at 70 percent and for week 3 it is five sets of 5 at 75 percent. These add volume. You can read the weight from the first set in the calculator's result for the week.
Common mistakes
- Using a true one-rep max as the training max. Start at 90 percent of it.
- Going to failure on the AMRAP set. Stop when the bar speed drops.
- Adding more weight than the program says. Add 5 or 10 pounds after the cycle.
- Using one training max for every lift. Each lift has its own.
What next
Use this often? Add 531 Lifting to your Home screen.
Frequently asked questions
What is a 5/3/1 lifting calculator?
A tool that turns your one-rep max or training max into the weights for each set of Jim Wendler's 5/3/1 program.
How do I find my training max for 5/3/1?
Take 90 percent of your estimated one-rep max, as the Fitness Wiki's 5/3/1 for Beginners page says.
What are the 5/3/1 percentages?
Week 1: 65, 75 and 85 percent for 5, 5 and 5+. Week 2: 70, 80 and 90 percent for 3, 3 and 3+. Week 3: 75, 85 and 95 percent for 5, 3 and 1+.
How much do I add to my training max?
5 pounds for the bench press and overhead press and 10 pounds for the squat and deadlift after each cycle.
What does the plus sign mean in 5/3/1?
It marks an AMRAP set: as many good reps as you can, without going to absolute failure.
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.